Drive Modes (Ackermann Rover)
Flight modes (or more accurately "Drive modes" for ground vehicles) provide autopilot support to make it easier to manually drive the vehicle or to execute autonomous missions.
This section outlines all supported drive modes for Ackermann rovers.
For information on mapping RC control switches to specific modes see: Basic Configuration > Flight Modes.
WARNING
Selecting any other mode than those listed below will either stop the rover or can lead to undefined behaviour.
Manual Modes
Manual modes require stick inputs from the user to drive the vehicle.
The sticks provide the same "high level" control effects over direction and rate of movement in all manual modes:
Left stick up/down
: Drive the rover forwards/backwards (controlling speed)Right stick left/right
: Make a left/right turn (controlling steering angle (Manual mode) or lateral acceleration (Acro and Position)).
The manual modes provide progressively increasing levels of autopilot support for maintaining a course, speed, and rate of turn, compensating for external factors such as slopes or uneven terrain.
Mode | 特性 |
---|---|
Manual | No autopilot support. User is responsible for keeping the rover on the desired course and maintaining speed and rate of turn. |
Acro | + Maintains the lateral acceleration. This makes it feel more like driving a car than manual mode. + It also protects against roll over and is slightly better at holding a straight line in uneven terrain. |
Position | + Best mode for holding a straight line. + Maintains speed against disturbances, e.g. when driving up a hill + Allows maximum speed to be limited. |
Details
Overview mode mapping to control effect
Mode | Forward speed | Steering angle/lateral acceleration | Required measurements |
---|---|---|---|
Manual | Directly map stick input to motor command. | Directly map stick input to steering angle. | None. |
Acro | Directly map stick input to motor command. | Stick input creates a lateral acceleration setpoint for the control system to regulate. | Lateral acceleration. |
Position | Stick input creates a speed setpoint for the control system to regulate. | Stick input creates a lateral acceleration setpoint for the control system to regulate. If this setpoint is zero (stick is centered) the control system will keep the rover driving in a straight line. | Lateral acceleration, yaw, speed and global position (GPS). |
手动模式
In this mode the stick inputs are directly mapped to motor commands. The rover does not attempt to maintain a specific orientation or compensate for external factors like slopes or uneven terrain! The user is responsible for making the necessary adjustments to the stick inputs to keep the rover on the desired course.
Stick | Effect |
---|---|
Left stick up/down | Drive the rover forwards/backwards. |
Right stick left/right | Move the steering angle to the left/right. |
For the configuration/tuning of this mode see Manual mode.
Acro Mode
INFO
This mode requires a lateral acceleration measurement.
In this mode the vehicle regulates its lateral acceleration to a setpoint (but does not stabilize heading or regulate speed).
Lateral acceleration can be directly mapped to a steering input based on the forward speed of the rover:
with
Wheel base, Steering angle, Forward speed.
For driving this means that the same right hand stick input will cause a different steering angle based on how fast you are driving. By limiting the maximum lateral acceleration, we can restrict the steering angle based on the speed, which can prevent the rover from rolling over. This mode will feel more like "driving a car" than Manual mode.
INFO
The lateral acceleration is only close loop controlled when driving forwards. When driving backwards the lateral acceleration setpoint is directly mapped to a steering angle using the equation above. This is due to the fact that rear wheel steering (driving a car with front-wheel steering backwards) is non-minimum-phase w.r.t to the lateral acceleration which leads to instabilities when doing closed loop control.
Stick | Effect |
---|---|
Left stick up/down | Drive the rover forwards/backwards. |
Right stick left/right | Create a lateral acceleration setpoint for the control system to regulate. If this input is zero the control system will attempt to maintain a zero lateral acceleration (minimal disturbance rejection) |
For the configuration/tuning of this mode see Acro mode.
Position Mode
INFO
This mode requires a lateral acceleration, yaw, speed and global position estimate.
This is the manual mode with the most autopilot support. The vehicle regulates its lateral acceleration and speed to a setpoint. If the lateral acceleration setpoint is zero, the controller will remember the gps coordinates and yaw (heading) of the vehicle and use those to construct a line that the rover will then follow (course control). This offers the highest amount of disturbance rejection, which leads to the best straight line driving behavior.
Stick | Effect |
---|---|
Left stick up/down | Stick position sets a forward/back speed setpoint. The vehicle attempts to maintain this speed on slopes etc. |
Right stick left/right | Create a lateral acceleration setpoint for the control system to regulate. If this input is zero the control system will maintain the course of the rover. |
For the configuration/tuning of this mode see Position mode.
Auto Modes
In auto modes the autopilot takes over control of the vehicle to run missions, return to launch, or perform other autonomous navigation tasks. For the tuning process see the configuration for Auto modes.
Mission Mode
Mission mode is an automatic mode that causes the vehicle to execute a predefined autonomous mission plan that has been uploaded to the flight controller. The mission is typically created and uploaded with a Ground Control Station (GCS) application, such as QGroundControl.
Mission commands
The following commands can be used in missions at time of writing (main(PX4 v1.16+)
):
QGC mission item | 通信 | 描述 |
---|---|---|
Mission start | MAV_CMD_MISSION_START | Starts the mission. |
Waypoint | MAV_CMD_NAV_WAYPOINT | Navigate to waypoint. |
Return to launch | MAV_CMD_NAV_RETURN_TO_LAUNCH | Return to the launch location. |
Delay until | MAV_CMD_NAV_DELAY | The rover will stop for a specified amount of time. |
Change speed | MAV_CMD_DO_CHANGE_SPEED | Change the speed setpoint |
Set launch location | MAV_CMD_DO_SET_HOME | Changes launch location to specified coordinates. |
Jump to item (all) | MAV_CMD_DO_JUMP (and other jump commands) | Jump to specified mission item. |
Loiter (all) | MAV_CMD_NAV_LOITER_TIME (and other loiter commands) | Stop the rover for given time. Other commands stop indefinitely. |
Return Mode
This mode uses the pure pursuit guidance logic with the launch position as goal. Return mode can be activated through the respective mission command or through the ground station UI.