# AirSim 仿真

FlightGear (opens new window) is a flight simulator with powerful FDM engines (opens new window). This allows FlightGear to simulate rotorcrafts under various meteorological conditions (which is why the bridge was originally developed by ThunderFly s.r.o. (opens new window)).

This page describes FlightGear's single-vehicle use in SITL. For information about multi-vehicle use see: Multi-Vehicle Simulation with FlightGear.

Supported Vehicles: Autogyro, Plane, Rover.

@{% youtube %}https://www.youtube.com/watch?v=iqdcN5Gj4wI{% endyoutube %}

Mermaid Graph (opens new window)

注解

See Simulation for general information about simulators, the simulation environment, and simulation configuration (e.g. supported vehicles).

# Installation (Ubuntu Linux)

注解

These instructions were tested on Ubuntu 18.04

  1. Install the usual Development Environment on Ubuntu LTS / Debian Linux.
  2. Install FlightGear:
    sudo add-apt-repository ppa:saiarcot895/flightgear
    sudo apt update
    sudo apt install flightgear
    
    This installs the latest stable FlightGear version from the PAA repository along with the FGdata package.

提示

For some models (e.g. those with electric engines) the daily build with the newest features may be necessary. Install this using the daily build PPA (opens new window).

  1. Check that you are able to run FlightGear:
    fgfs --launcher
    
  2. Set write permissions to the Protocols folder in the FlightGear installation directory:
    sudo chmod a+w /usr/share/games/flightgear/Protocol
    
    Setting the permissions is required because the PX4-FlightGear-Bridge puts the communication definition file here.

Additional installation instructions can be found on FlightGear wiki (opens new window).

# 运行仿真

Run a simulation by starting PX4 SITL, specifying the airframe configuration of your choice.

以上指令启动了一个具有完整 UI 的载具。 For example, to start a plane simulation :

cd /path/to/PX4-Autopilot
make px4_sitl_nolockstep flightgear_rascal

The supported vehicles and make commands are listed below (click on the links to see the vehicle images).

载具类型 指令
标准构型的固定翼飞机 make px4_sitl_nolockstep flightgear_rascal
Ackerman 车 (UGV/Rover) make px4_sitl_nolockstep flightgear_tf-r1
旋翼机 make px4_sitl_nolockstep flightgear_tf-g1

The commands above launch a single vehicle with the full UI. QGroundControl should be able to automatically connect to the simulated vehicle.

注解

For the full list of FlightGear build targets (highlighted) run:

make px4_sitl_nolockstep list_vmd_make_targets | grep flightgear_

For additional information see: FlightGear Vehicles (this includes information about "unsupported" vehicles, and adding new vehicles). 一旦 INFO 打印出的 [ecl/EKF] 状态为 commencing GPS fusion ,则表明该载具已准备就绪可以解锁。

注解

The Installing Files and Code guide is a useful reference if there are build errors.

# 让飞行器起飞

你可以通过输入以下指令让飞机起飞:

Once the PX4 has started it will launch the PX4 shell as shown below. You must select enter to get the command prompt.

______  __   __    ___
| ___ \ \ \ / /   /   |
| |_/ /  \ V /   / /| |
|  __/   /   \  / /_| |
| |     / /^\ \ \___  |
\_|     \/   \/     |_/

px4 starting.

INFO  [px4] Calling startup script: /bin/sh etc/init.d-posix/rcS 0
INFO  [param] selected parameter default file eeprom/parameters_1034
I'm Mavlink to FlightGear Bridge
Targed Bridge Freq: 200, send data every step: 1
4
  5   -1
  7   -1
  2   1
  4   1
[param] Loaded: eeprom/parameters_1034
INFO  [dataman] Unknown restart, data manager file './dataman' size is 11798680 bytes
INFO  [simulator] Waiting for simulator to accept connection on TCP port 4560
INFO  [simulator] Simulator connected on TCP port 4560.
INFO  [commander] LED: open /dev/led0 failed (22)
INFO  [commander] Mission #3 loaded, 9 WPs, curr: 8
INFO  [init] Mixer: etc/mixers-sitl/plane_sitl.main.mix on /dev/pwm_output0
INFO  [mavlink] mode: Normal, data rate: 4000000 B/s on udp port 18570 remote port 14550
INFO  [airspeed_selector] No airspeed sensor detected. Switch to non-airspeed mode.
INFO  [mavlink] mode: Onboard, data rate: 4000000 B/s on udp port 14580 remote port 14540
INFO  [mavlink] mode: Onboard, data rate: 4000 B/s on udp port 14280 remote port 14030
INFO  [logger] logger started (mode=all)
INFO  [logger] Start file log (type: full)
INFO  [logger] Opened full log file: ./log/2020-04-28/22_03_36.ulg
INFO  [mavlink] MAVLink only on localhost (set param MAV_{i}_BROADCAST = 1 to enable network)
INFO  [px4] Startup script returned successfully
pxh> StatsHandler::StatsHandler() Setting up GL2 compatible shaders
Now checking for plug-in osgPlugins-3.4.1/osgdb_nvtt.so
PX4 Communicator: PX4 Connected.

pxh>

The console will print out status as PX4 loads the airframe-specific initialization and parameter files, wait for (and connect to) the simulator. Once there is an INFO print that [ecl/EKF] is commencing GPS fusion the vehicle is ready to arm. At this point, you should see a FlightGear window with some view of aircraft.

注解

You can change the view by pressing Ctrl+V.

FlightGear UI

例如:

pxh> commander takeoff

# 使用/配置选项

You can tune your FG installation/settings by the following environment variables:

  • FG\_BINARY - absolute path to FG binary to run. (It can be an AppImage)
  • FG\_MODELS\_DIR - absolute path to the folder containing the manually-downloaded aircraft models which should be used for simulation.
  • FG\_ARGS\_EX - any additional FG parameters.

# Display the frame rate

In FlightGear you can display the frame rate by enabling it in: View > View Options > Show frame rate.

# 带光流的四旋翼

Takeoff location in SITL FlightGear can be set using additional variables. Setting the variable will override the default takeoff location.

The variables which can be set are as follows: --airport, --runway, and --offset-distance. Other options can be found on FlightGear wiki (opens new window)

For example:

FG_ARGS_EX="--airport=PHNL"  make px4_sitl_nolockstep flightgear_rascal

The example above starts the simulation on the Honolulu international airport (opens new window)

# 模拟一个 Wifi 无人机

Joystick and thumb-joystick are supported through QGroundControl (setup instructions here).

The joystick input in FlightGear should be disabled in otherwise there will be a "race condition" between the FG joystick input and PX4 commands.

# 扩展与定制

To extend or customize the simulation interface, edit the files in the *Tools/flightgear_bridge folder. The code is available in the PX4-FlightGear-Bridge repository (opens new window) on Github.

# 更多信息