# ARK GPS
# Where to Buy
Order this module from:
- Open Source Schematic and BOM (opens new window)
- Runs PX4 Open Source Firmware (opens new window)
- Supports UAVCAN Firmware Updating
- Dynamic UAVCAN node enumeration
- Ublox M9N GPS
- Ultra-robust meter-level GNSS positioning
- Maximum position availability with concurrent reception of 4 GNSS
- Advanced spoofing and jamming detection
- Excellent RF interference mitigation
- Bosch BMM150 Magnetometer
- Bosch BMP388 Barometer
- Invensense ICM-42688-P 6-Axis IMU
- Ublox M9N GPS
- STM32F412CEU6 MCU
- Safety Button
- Two Pixhawk Standard CAN Connectors
- 4 Pin JST GH
- Pixhawk Standard Debug Connector
- 6 Pin JST SH
- Small Form Factor
- 5cm x 5cm x 1cm
- LED Indicators
- Safety LED
- GPS Fix
- RGB System Status
- USA Built
- Power Requirements
- 110mA Average
- 117mA Max
ARK GPS is connected to the CAN bus using a Pixhawk standard 4 pin JST GH cable. Multiple sensors can be connected by plugging additional sensors into ARK GPS's second CAN connector.
General instructions for UAVCAN wiring can also be found in UAVCAN > Wiring.
The recommended mounting orientation is with the connectors on the board pointing towards the back of vehicle.
The sensor can be mounted anywhere on the frame, but you will need to specify its position, relative to vehicle centre of gravity, during PX4 configuration.
# PX4 Setup
# Enabling UAVCAN
The steps are:
- In QGroundControl set the parameter UAVCAN_ENABLE to
3and reboot (see Finding/Updating Parameters).
- Connect ARK GPS CAN to the Pixhawk CAN.
Once enabled, the module will be detected on boot. GPS data should arrive at 10Hz.
General instructions for UAVCAN PX4 configuration can also be found in UAVCAN > PX4 Configuration.
# PX4 Configuration
You need to set necessary UAVCAN parameters and define offsets if the sensor is not centred within the vehicle.
- Enable GPS yaw fusion by setting bit 7 of EKF2_AID_MASK to true.
- Enable UAVCAN_SUB_GPS, UAVCAN_SUB_MAG, and UAVCAN_SUB_BARO.
- Set CANNODE_TERM to
1if this is that last node on the CAN bus.
- The parameters EKF2_GPS_POS_X, EKF2_GPS_POS_Y and EKF2_GPS_POS_Z can be set to account for the offset of the ARK GPS from the vehicles centre of gravity.
# Building ARK GPS Firmware
ARK GPS is sold with a recent firmware build. Developers who want to update to the very latest version can build and install it themselves using the normal PX4 toolchain and sources.
The steps are:
Install the PX4 toolchain.
Clone the PX4-Autopilot sources, including ARK GPS, using git:
git clone https://github.com/PX4/PX4-Autopilot --recursive cd PX4-Autopilot
Build the ARK GPS firmware:
That will have created a binary in build/ark_can-gps_default named XX-X.X.XXXXXXXX.uavcan.bin. Put this binary on the root directory of the flight controller’s SD card to flash the ARK GPS. Next time you power your flight controller with the SD card installed, ARK GPS will automatically be flashed and you should notice the binary is no longer in the root directory and there is now a file named 80.bin in the ufw directory of the SD card.
The ARK GPS will not boot if there is no SD card in the flight controller when powered on. :::
# Updating ARK GPS Bootloader
The ARK GPS comes with the bootloader pre-installed. You can, however, rebuild and reflash it within the PX4-Autopilot environment.
The steps are:
- Build the ARK GPS bootloader firmware:
This will setup your
launch.json file if you are in VS code. If using the Black Magic Probe and VS code, make sure to update
BMPGDBSerialPort within this file to the correct port that your debugger is connected to. On MacOS, the port name should look something like
- Connect your ARK GPS to any Serial Wire Debugging (SWD) device that supports use of GNU Project Debugger (GDB), such as the Black Magic Probe and then connect power to your ARK GPS via one of the CAN ports.
- Flash the ARK GPS with
ark_can-gps_canbootloader. To do so in VS code, you should see
CMake: [ark_can-gps_canbootloader]: Readyon the bottom bar of VS code, indicating what you are flashing. You then flash the bootloader by selecting
Start Debuggingin the Run and Debug window of VS code.
- With the bootloader flashed, you are ready to build and flash the ARK GPS firmware
ark_can-gps_defaultas outlined above.
# LED Meanings
You will see green, blue and red LEDs on the ARK GPS when it is being flashed, and a blinking green LED if it is running properly.
If you see a red LED there is an error and you should check the following:
- Make sure the flight controller has an SD card installed.
- Make sure the ARK GPS has
ark_can-gps_canbootloaderinstalled prior to flashing
- Remove binaries from the root and ufw directories of the SD card and try to build and flash again.