# Holybro Kakute H7
PX4 does not manufacture this (or any) autopilot. Contact the [manufacturer](https://shop.holybro.com/) for hardware support or compliance issues.
The Holybro Kakute H7 (opens new window) is full of features including dual plug-and-play 4in1 ESC ports, HD camera plug, barometer, OSD, 6x UARTs, full Blackbox MicroSD card slot, 5V and 9V BEC, easy soldering layout, and much more.
The Kakute H7 builds upon the best features of its predecessor, the Kakute F7, and further improves on hardware components and layout. Dual plug'n'play 4-in-1 ESC connectors simplify support for x8 and Octocopter configurations, keeping assembly simple and clean.
The board also has an on-board barometer, LED & buzzer pad, and I2C pad (SDA & SCL) for external GPS/Magnetometers.
This flight controller is manufacturer supported.
# Key Features
- MCU: STM32H743 32-bit processor running at 480 MHz
- IMU: MPU6000
- Barometer: BMP280
- OSD: AT7456E
- Onboard Bluetooth chip: Disabled with PX4
- 2x JST-SH1.0_8pin port (For Single or 4in1 ESCs, x8/Octocopter plug & play compatible)
- 1x JST-GH1.5_6pin port (For HD System like Caddx Vista & Air Unit)
- Battery input voltage: 2S - 8S
- BEC 5V 2A Cont.
- BEC 9V 1.5A Cont.
- Mounting: 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets
- Dimension: 35x35mm
- Weight: 8g
# Where to Buy
The board can be bought from one of the following shops (for example):
The Kakute H7 is designed to work with the Tekko32 4-in-1 ESC and they can be bought in combination.
# Connectors and Pins
This is the silkscreen for the Kakute H7, showing the top of the board:
|B+||Battery positive voltage (2S-8S)|
|SDA, SCL||I2C connection (for peripherals)|
|5V||5V output (2A max)|
|3V3||3.3V output (0.25A max)|
|VI||Video input from FPV camera|
|VO||Video output to video transmitter|
|CAM||To camera OSD control|
|G or GND||Ground|
|RSI||Analog RSSI (0-3.3V) input from receiver|
|R1, T1||UART1 RX and TX||TELEM1|
|R3, T3||UART3 RX and TX||NuttX debug console|
|R4, T4||UART4 RX and TX||GPS1|
|R6, T6||UART6 RX and TX (R6 also located in the GH plug)||RC port|
|R7||UART7 RX (RX is located in the plugs for use with 4-in-1 ESCs)||DShot telemetry|
|LED||WS2182 addressable LED signal wire (not tested)|
|Z-||Piezo buzzer negative leg (Connect buzzer positive leg to 5V pad)|
|M1 to M4||Motor signal outputs (located in plug for use in 4-in-1 ESCs)|
|M5 to M8||Motor signal outputs (located in plug for use in 4-in-1 ESCs)|
# PX4 Bootloader Update
The board comes pre-installed with Betaflight (opens new window). Before PX4 firmware can be installed, the PX4 bootloader must be flashed. Download the kakuteh7_bl.hex (opens new window) bootloader binary and read this page for flashing instructions.
# Building Firmware
To build PX4 for this target:
# Installing PX4 Firmware
The firmware can be installed in any of the normal ways:
- Build and upload the source
make holybro_kakuteh7_default upload
- Load the firmware using QGroundControl. You can use either pre-built firmware or your own custom firmware.
KakuteH7 is supported with PX4 master & PX4 v1.13 or newer. If you are loading the pre-built firmware via QGroundcontrol, you must use QGC Daily or QGC verision newer than 4.1.7.
# PX4 Configuration
In addition to the basic configuration, the following parameters are important:
|SYS_HAS_MAG||This should be disabled since the board does not have an internal mag. You can enable it if you attach an external mag.|
|MOT_ORDERING||If you use a 4-in-1 ESC with Betaflight motor assignment, this parameter can be set accordingly.|
# Serial Port Mapping
|UART7||/dev/ttyS5||ESC telemetry (DShot)|
# Debug Port
# System Console
UART3 RX and TX are configured for use as the System Console.
The SWD interface (JTAG) pins are:
SWCLK: Test Point 2 (Pin 72 on the CPU)
SWDIO: Test Point 3 (Pin 76 on CPU)
GND: As marked on board
VDD_3V3: As marked on board
These are shown below.