# Kakute F7

PX4 does not manufacture this (or any) autopilot. Contact the [manufacturer](https://shop.holybro.com/) for hardware support or compliance issues.

The Kakute F7 from Holybro is a flight controller board designed for racers.


This flight controller is manufacturer supported.

# 主要特性

  • Main System-on-Chip: STM32F745VGT6 (opens new window)
    • CPU: 216 MHz ARM Cortex M7 with single-precision FPU
    • RAM: 320 KB SRAM
    • FLASH: 1 MB
  • Standard racer form factor: 36x36 mm with standard 30.5 mm hole pattern
  • ICM20689 Accel / Gyro (Soft-mounted)
  • BMP280 Baro
  • microSD (for logging)
  • 6 UARTs
  • 1 I2C bus
  • 6 路 PWM 输出
  • Built-in OSD chip (AB7456 via SPI)

# 在哪里买

The board can be bought from one of the following shops (for example):


The Kakute F7 is designed to work with the Tekko32 4-in-1 ESC and they can be bought in combination.

# Connectors and Pins

This is the silkscreen for the Kakute F7, showing the top of the board:

Kakute F7 Silkscreen

针脚 功能 PX4 default
B+ Battery positive voltage (2S-6S)
5V 5V output (2A max)
VO Video output to video transmitter
VI Video input from FPV camera
G or GND Ground
SDA, SCL I2C connection (for peripherals)
R3, T3 UART3 RX and TX NuttX debug console
R4, T4 UART4 RX and TX GPS1
R6, T6 UART6 RX and TX RC port
R7, T7 UART7 RX and TX (RX is located in the plug for use with 4-in-1 ESCs) DShot telemetry
LED WS2182 addressable LED signal wire (not tested)
Buz- Piezo buzzer negative leg (Connect buzzer positive leg to 5V pad)
3V3 3.3V output (200 mA max)
M1 to M4 Motor signal outputs (located in plug for use in 4-in-1 ESCs)
M5, M6 Additional motor signal outputs (located on side of board)
RSI Analog RSSI (0-3.3V) input from receiver
Boot Bootloader button

# PX4 Bootloader Update

The board comes pre-installed with Betaflight (opens new window). Before PX4 firmware can be installed, the PX4 bootloader must be flashed. Download the kakutef7_bl.hex (opens new window) bootloader binary and read this page for flashing instructions.

# 编译固件

To build PX4 for this target:

make holybro_kakutef7_default

# Installing PX4 Firmware

The firmware can be installed in any of the normal ways:

  • Build and upload the source make holybro_kakutef7_default upload
  • Load the firmware using QGroundControl. You can use either pre-built firmware or your own custom firmware.

# 配置

In addition to the basic configuration, the following parameters are important:

参数 设置
SYS_HAS_MAG This should be disabled since the board does not have an internal mag. You can enable it if you attach an external mag.
MOT_ORDERING If you use a 4-in-1 ESC with Betaflight/Cleanflight motor assignment, this parameter can be set accordingly.

# Serial Port Mapping

UART 设备 Port
USART1 /dev/ttyS0 TELEM1
USART2 /dev/ttyS1 TELEM2
USART3 /dev/ttyS2 Debug Console
UART4 /dev/ttyS3 GPS1
USART6 /dev/ttyS4 RC SBUS
UART7 /dev/ttyS5 ESC telemetry (DShot)

# 调试接口

# 系统控制台

UART3 RX and TX are configured for use as the System Console.


The SWD interface (JTAG) pins are:

  • SWCLK: Test Point 2 (Pin 72 on the CPU)
  • SWDIO: Test Point 3 (Pin 76 on CPU)
  • GND: As marked on board
  • VDD_3V3: As marked on board

These are shown below.

SWD Pins on Kakute F7 - CLK SWO SWD Pins on Kakute F7:  GND and VDD_3V3