# Camera Trigger
The camera trigger driver allows the use of the AUX ports to send out pulses in order to trigger a camera.
In addition to a pulse being sent out, the MAVLink CAMERA_TRIGGER (opens new window) message is published containing a sequence number (i.e. the current session's image sequence number) and the corresponding timestamp. This timestamp can be used for several applications, including: timestamping photos for aerial surveying and reconstruction, synchronising a multi-camera system or visual-inertial navigation.
Cameras can also (optionally) use the flight controller camera capture pin to signal the exact moment that a photo/frame is taken. This allows more precise mapping of images to GPS position for geotagging, or the right IMU sample for VIO synchronization, etc.
# Trigger Configuration
Camera triggering is usually configured from the QGroundControl Vehicle Setup > Camera (opens new window) section.
The camera settings section is not available by default for FMUv2-based flight controllers (e.g. 3DR Pixhawk) because the camera module is not automatically included in firmware. For more information see Finding/Updating Parameters > Parameters Not In Firmware.
# Trigger Modes
Four different modes are supported, controlled by the TRIG_MODE parameter:
|0||Camera triggering is disabled.|
|1||Works like a basic intervalometer that can be enabled and disabled by using the MAVLink command |
|2||Switches the intervalometer constantly on.|
|3||Triggers based on distance. A shot is taken every time the set horizontal distance is exceeded. The minimum time interval between two shots is however limited by the set triggering interval.|
|4||triggers automatically when flying a survey in Mission mode.|
If it is your first time enabling the camera trigger app, remember to reboot after changing the
# Trigger Hardware Configuration
The pins used to trigger image capture for GPIO, PWM or Seagull-based triggering (i.e. when not using a MAVLink camera) are set using the TRIG_PINS parameter. The default is 56, which means that trigger is enabled on FMU pins 5 and 6.
On a Pixhawk flight controller that has both FMU and I/O boards these FMU pins map to
AUX6 (e.g. Pixhawk 4, CUAV v5+). On a controller that only has an FMU, the pins map to
MAIN6 (e.g. Pixhawk 4 mini, CUAV v5 nano). At time of writing triggering only works on FMU pins - you can't trigger a camera using pins on the I/O board.
TRIG_PINS=56 (default) you can use the AUX pins 1 to 4 as actuator outputs (for servos/ESCs). With
TRIG_PINS=78, you can use the AUX pins 1-6 as actuator outputs. Any other combination of pins can be selected, but this will disable use of the other FMU pins as outputs.
# Trigger Interface Backends
The camera trigger driver supports several backends - each for a specific application, controlled by the TRIG_INTERFACE parameter:
|1||enables the GPIO interface. The AUX outputs are pulsed high or low (depending on the |
|2||Enables the Seagull MAP2 interface. This allows the use of the Seagull MAP2 (opens new window) to interface to a multitude of supported cameras. Pin/Channel 1 (camera trigger) and Pin/Channel 2 (mode selector) of the MAP2 should be connected to the lower and higher AUX pins of |
|3||Enables the MAVLink interface. In this mode, no actual hardware output is used. Only the |
|4||Enables the generic PWM interface. This allows the use of infrared triggers (opens new window) or servos to trigger your camera. The trigger signal is duplicated on both pins specified using |
|TRIG_POLARITY||Relevant only while using the GPIO interface. Sets the polarity of the trigger pin. Active high means that the pin is pulled low normally and pulled high on a trigger event. Active low is vice-versa.|
|TRIG_INTERVAL||Defines the time between two consecutive trigger events in milliseconds.|
|TRIG_ACT_TIME||Defines the time in milliseconds the trigger pin is held in the "active" state before returning to neutral. In PWM modes, the minimum is limited to 40 ms to make sure we always fit an activate pulse into the 50Hz PWM signal.|
The full list of parameters pertaining to the camera trigger module can be found on the parameter reference page.
# Camera Capture
Cameras can also (optionally) use the flight controller camera capture pin to signal the exact moment when a photo/frame is taken. This allows more precise mapping of images to GPS position for geotagging, or the right IMU sample for VIO synchronization, etc.
Camera capture/feedback is enabled in PX4 by setting CAM_CAP_FBACK = 1. The capture pin used depends on the hardware:
- Pixhawk FMUv5x boards use the board-specific camera capture pin (PI0).
- Other board use FMU PWM pin 6 (hardcoded) for camera capture.
PX4 detects a rising edge with the appropriate voltage level on the camera capture pin (for Pixhawk flight controllers this is normally 3.3V). If the camera isn't outputing an appropriate voltage, then additional circuitry will be required to make the signal compatible.
Cameras that have a hotshoe connector (for connecting a flash) can usually be connected via a hotshoe-adaptor. For example, the Seagull #SYNC2 Universal Camera Hot Shoe Adapter (opens new window) is an optocoupler that decouples and shifts the flash voltage to the Pixhawk voltage. This slides into the flash slot on the top of the camera. The red and black ouptputs are connected to the servo rail/ground and the white wire is connected to the input capture pin.
PX4 emits the MAVLink [CAMERA_TRIGGER](https://mavlink.io/en/messages/common.html#CAMERA_TRIGGER) message on both camera trigger and camera capture. If camera capture is configured, the timestamp from the camera capture driver is used, otherwise the triggering timestamp.
# Command Interface
TODO : NEEDS UPDATING updating
The camera trigger driver supports several commands:
MAV_CMD_DO_TRIGGER_CONTROL (opens new window) - Accepted in "command controlled" mode (
|Param #1||Trigger enable/disable (set to 0 for disable, 1 for start)|
|Param #2||Trigger cycle time in milliseconds (sets the |
|Param #3||Sequence reset (set to 1 to reset image sequence number, 0 to keep current sequence number)|
MAV_CMD_DO_DIGICAM_CONTROL (opens new window) - Accepted in all modes. This is used by the GCS to test-shoot the camera from the user interface. The trigger driver does not yet support all camera control parameters defined by the MAVLink spec.
|Param #5||Trigger one-shot command (set to 1 to trigger a single image frame).|
MAV_CMD_DO_SET_CAM_TRIGG_DIST (opens new window) - Accepted in "mission controlled" mode (
This command is autogenerated during missions to trigger the camera based on survey missions from the GCS.
# Testing Trigger Functionality
On the PX4 console:
Click on Trigger Camera in the main instrument panel. These shots are not logged or counted for geotagging.
# Sony QX-1 example (Photogrammetry)
In this example, we will use a Seagull MAP2 trigger cable to interface to a Sony QX-1 and use the setup to create orthomosaics after flying a fully autonomous survey mission.
# Trigger Settings
The recommended camera settings are:
- Leave the remaining parameters at their defaults.
You will need to connect the Seagull MAP2 to the auxiliary/FMU pins on your autopilot. Pin 1 goes to
AUX 5, and Pin 2 to
AUX 6. The other end of the MAP2 cable will go into the QX-1's "MULTI" port.
# Camera Configuration
We use a Sony QX-1 with a 16-50mm f3.5-5.6 lens for this example.
To avoid autofocus and metering lag when the camera is triggered, the following guidelines should be followed:
- Manual focus to infinity
- Set camera to continuous shooting mode
- Manually set exposure and aperture
- ISO should be set as low as possible
- Manual white balance suitable for scene
Download/copy the logfile and images from the flight and point QGroundControl to them. Then click on "Start Tagging".
You can verify the geotagging using a free online service like Pic2Map (opens new window). Note that Pic2Map is limited to only 40 images.
We use Pix4D (opens new window) for 3D reconstruction.
# Camera-IMU sync example (VIO)
In this example, we will go over the basics of synchronising IMU measurements with visual data to build a stereo Visual-Inertial Navigation System (VINS). To be clear, the idea here isn't to take an IMU measurement exactly at the same time as we take a picture but rather to correctly time stamp our images so as to provide accurate data to our VIO algorithm.
The autopilot and companion have different clock bases (boot-time for the autopilot and UNIX epoch for companion), so instead of skewing either clock, we directly observe the time offset between the clocks. This offset is added or subtracted from the timestamps in the MAVLink messages (e.g
HIGHRES_IMU) in the cross-middleware translator component (e.g MAVROS on the companion and
mavlink_receiver in PX4). The actual synchronisation algorithm is a modified version of the Network Time Protocol (NTP) algorithm and uses an exponential moving average to smooth the tracked time offset. This synchronisation is done automatically if MAVROS is used with a high-bandwidth onboard link (MAVLink mode
For acquiring synchronised image frames and inertial measurements, we connect the trigger inputs of the two cameras to a GPIO pin on the autopilot. The timestamp of the inertial measurement from start of exposure and a image sequence number is recorded and sent to the companion computer (
CAMERA_TRIGGER message), which buffers these packets and the image frames acquired from the camera. They are matched based on the sequence number (first image frame is sequence 0), the images timestamped (with the timestamp from the
CAMERA_TRIGGER message) and then published.
The following diagram illustrates the sequence of events which must happen in order to correctly timestamp our images.
# Step 1
First, set the TRIG_MODE to 1 to make the driver wait for the start command and reboot your FCU to obtain the remaining parameters.
# Step 2
For the purposes of this example we will be configuring the trigger to operate in conjunction with a Point Grey Firefly MV camera running at 30 FPS.
TRIG_INTERVAL: 33.33 ms
TRIG_POLARITY: 0 (active low)
TRIG_ACT_TIME: 0.5 ms. The manual specifies it only has to be a minimum of 1 microsecond.
TRIG_MODE: 1, because we want our camera driver to be ready to receive images before starting to trigger. This is essential to properly process sequence numbers.
TRIG_PINS: 56, Leave default.
# Step 3
Wire up your cameras to your AUX port by connecting the ground and signal pins to the appropriate place.
# Step 4
You will have to modify your driver to follow the sequence diagram above. Public reference implementations for IDS Imaging UEye (opens new window) cameras and for IEEE1394 compliant (opens new window) cameras are available.