Pixracer

The Pixhawk® XRacer board family is optimized for small racing quads and planes. In contrast to Pixfalcon and Pixhawk it has in-built Wifi, new sensors, convenient full servo headers, CAN and supports 2M flash.

Key Features

  • Main System-on-Chip: STM32F427VIT6 rev.3
    • CPU: 180 MHz ARM Cortex® M4 with single-precision FPU
    • RAM: 256 KB SRAM (L1)
  • Standard FPV form factor: 36x36 mm with standard 30.5 mm hole pattern
  • Invensense® ICM-20608 Accel / Gyro (4 KHz) / MPU9250 Accel / Gyro / Mag (4 KHz)
  • HMC5983 magnetometer with temperature compensation
  • Measurement Specialties MS5611 barometer
  • JST GH connectors
  • microSD (logging)
  • Futaba S.BUS and S.BUS2 / Spektrum DSM2 and DSMX / Graupner SUMD / PPM input / Yuneec ST24
  • FrSky® telemetry port
  • OneShot PWM out (configurable)
  • Optional: Safety switch and buzzer

Where to Buy

Pixracer is available from the mRobotics.io.

Accessories include:

Kit

The Pixracer is designed to use a separate avionics power supply. This is necessary to avoid current surges from motors or ESCs to flow back to the flight controller and disturb its delicate sensors.

  • Power module (with voltage and current sensing)
  • I2C splitter (supporting AUAV, Hobbyking and 3DR® peripherals)
  • Cable kit for all common peripherals

Wifi (no USB required)

One of the main features of the board is its ability to use Wifi for flashing new firmware, system setup and in-flight telemetry. This frees it of the need of any desktop system.

Setup and telemetry are already available, firmware upgrade is already supported by the default bootloader but not yet enabled

Wiring Diagrams

Grau setup pixracer top

Grau setup pixracer bottom

setup pixracer GPS

Grau b Pixracer FrSkyS.Port Connection

Grau ACSP4 2 roh

Grau ACSP5 roh

Connectors

All connectors follow the Dronecode connector standard. Unless noted otherwise all connectors are JST GH.

Pinouts

TELEM1, TELEM2+OSD ports

Pin Signal Volt
1 (red) VCC +5V
2 (blk) TX (OUT) +3.3V
3 (blk) RX (IN) +3.3V
4 (blk) CTS (IN) +3.3V
5 (blk) RTS (OUT) +3.3V
6 (blk) GND GND

GPS port

Pin Signal Volt
1 (red) VCC +5V
2 (blk) TX (OUT) +3.3V
3 (blk) RX (IN) +3.3V
4 (blk) I2C1 SCL +3.3V
5 (blk) I2C1 SDA +3.3V
6 (blk) GND GND

FrSky Telemetry / SERIAL4

Pin Signal Volt
1 (red) VCC +5V
2 (blk) TX (OUT) +3.3V
3 (blk) RX (IN) +3.3V
4 (blk) GND GND

RC Input (accepts PPM / S.BUS / Spektrum / SUMD / ST24)

Pin Signal Volt
1 (red) VCC +5V
2 (blk) RC IN +3.3V
3 (blk) RSSI IN +3.3V
4 (blk) VDD 3V3 +3.3V
5 (blk) GND GND

CAN

Pin Signal Volt
1 (red) VCC +5V
2 (blk) CAN_H +12V
3 (blk) CAN_L +12V
4 (blk) GND GND

POWER

Pin Signal Volt
1 (red) VCC +5V
2 (blk) VCC +5V
3 (blk) CURRENT +3.3V
4 (blk) VOLTAGE +3.3V
5 (blk) GND GND
6 (blk) GND GND

SWITCH

Pin Signal Volt
1 (red) SAFETY GND
2 (blk) !IO_LED_SAFETY GND
3 (blk) VCC +3.3V
4 (blk) BUZZER- -
5 (blk) BUZZER+ -

Dronecode debug port (JST SM06B connector)

Pin Signal Volt
1 (red) VCC TARGET SHIFT +3.3V
2 (blk) CONSOLE TX (OUT) +3.3V
3 (blk) CONSOLE RX (IN) +3.3V
4 (blk) SWDIO +3.3V
5 (blk) SWCLK +3.3V
6 (blk) GND GND

Pixracer top pinouts

Pixracer bottom pinouts

Pixracer esp

Schematics

The reference is provided as: Altium Design Files

The following PDF files are provided for convenience only:

Building Firmware

Most users will not need to build this firmware! It is pre-built and automatically installed by QGroundControl when appropriate hardware is connected.

To build PX4 for this target:

make px4_fmu-v4_default

Credits

This design was created by Nick Arsov and Phillip Kocmoud and architected by Lorenz Meier, David Sidrane and Leonard Hall.

© PX4 Dev Team. License: CC BY 4.0            Updated: 2020-10-28 22:06:47

results matching ""

    No results matching ""