# Poor Man's Sampling Profiler
This section describes how you can use the Poor Man's Sampling Profiler (opens new window) (PMSP) shell script to assess the performance of PX4. This is an implementation of a known method originally invented by Mark Callaghan and Domas Mituzas (opens new window).
PMSP is a shell script that operates by interrupting execution of the firmware periodically in order to sample the current stack trace. Sampled stack traces are appended into a text file. Once sampling is finished (which normally takes about an hour or more), the collected stack traces are folded. The result of folding is another text file that contains the same stack traces, except that all similar stack traces (i.e. those that were obtained at the same point in the program) are joined together, and the number of their occurrences is recorded. The folded stacks are then fed into the visualization script, for which purpose we employ FlameGraph - an open source stack trace visualizer (opens new window).
# Basic Usage
The profiler relies on GDB to run PX4 on the embedded target. So before profiling a target, you must have the hardware you wish to profile, and you must compile and upload the firmware to that hardware. You will then need a SWD (JTAG) Hardware Debugging Interface, such as the DroneCode Probe, to run the GDB server and interact with the board.
# Determine the Debugger Device
poor-mans-profiler.sh automatically detects and uses the correct USB device if you use it with a DroneCode Probe.
If you use a different kind of probe you may need to pass in the specific device on which the debugger is located.
You can use the bash command
ls -alh /dev/serial/by-id/ to enumerate the possible devices on Ubuntu.
For example the following devices are enumerated with a Pixhawk 4 and DroneCode Probe connected over USB:
user@ubuntu:~/PX4-Autopilot$ ls -alh /dev/serial/by-id/
drwxr-xr-x 2 root root 100 Apr 23 18:57 .
drwxr-xr-x 4 root root 80 Apr 23 18:48 ..
lrwxrwxrwx 1 root root 13 Apr 23 18:48 usb-3D_Robotics_PX4_FMU_v5.x_0-if00 -> ../../ttyACM0
lrwxrwxrwx 1 root root 13 Apr 23 18:57 usb-Black_Sphere_Technologies_Black_Magic_Probe_BFCCB401-if00 -> ../../ttyACM1
lrwxrwxrwx 1 root root 13 Apr 23 18:57 usb-Black_Sphere_Technologies_Black_Magic_Probe_BFCCB401-if02 -> ../../ttyACM2
In this case, the script would automatically pick up the device named
But if you were using a different device you would be able discover the appropriate id from the listing above.
Then pass in the appropriate device using the
--gdbdev argument like this:
./poor-mans-profiler.sh --elf=build/px4_fmu-v4_default/px4_fmu-v4_default.elf --nsamples=30000 --gdbdev=/dev/ttyACM2
Basic usage of the profiler is available through the build system. For example, the following command builds and profiles px4_fmu-v4pro target with 10000 samples (fetching FlameGraph and adding it to the path as needed).
make px4_fmu-v4pro_default profile
For more control over the build process, including setting the number of samples, see the Implementation.
# Understanding the Output
A screenshot of an example output is provided below (note that it is not interactive here):
On the flame graph, the horizontal levels represent stack frames, whereas the width of each frame is proportional to the number of times it was sampled. In turn, the number of times a function ended up being sampled is proportional to the duration times frequency of its execution.
# Possible Issues
The script was developed as an ad-hoc solution, so it has some issues. Please watch out for them while using it:
If GDB is malfunctioning, the script may fail to detect that, and continue running. In this case, obviously, no usable stacks will be produced. In order to avoid that, the user should periodically check the file
/tmp/pmpn-gdberr.log, which contains the stderr output of the most recent invocation of GDB. In the future the script should be modified to invoke GDB in quiet mode, where it will indicate issues via its exit code.
Sometimes GDB just sticks forever while sampling the stack trace. During this failure, the target will be halted indefinitely. The solution is to manually abort the script and re-launch it again with the
--appendoption. In the future the script should be modified to enforce a timeout for every GDB invocation.
Multithreaded environments are not supported. This does not affect single core embedded targets, since they always execute in one thread, but this limitation makes the profiler incompatible with many other applications. In the future the stack folder should be modified to support multiple stack traces per sample.
The script is located at /platforms/nuttx/Debug/poor-mans-profiler.sh (opens new window)
Once launched, it will perform the specified number of samples with the specified time interval.
Collected samples will be stored in a text file in the system temp directory (typically
Once sampling is finished, the script will automatically invoke the stack folder, the output of which will be stored in an adjacent file in the temp directory.
If the stacks were folded successfully, the script will invoke the FlameGraph script and store the result in an interactive SVG file.
Please note that not all image viewers support interactive images;
it is recommended to open the resulting SVG in a web browser.
The FlameGraph script must reside in the
PATH, otherwise PMSP will refuse to launch.
PMSP uses GDB to collect the stack traces.
Currently it uses
arm-none-eabi-gdb, other toolchains may be added in the future.
In order to be able to map memory locations to symbols, the script needs to be referred to the executable file that is currently running on the target.
This is done with the help of the option
--elf=<file>, which expects a path (relative to the root of the repository) pointing to the location of the currently executing ELF.
./poor-mans-profiler.sh --elf=build/px4_fmu-v4_default/px4_fmu-v4_default.elf --nsamples=30000
Note that every launch of the script will overwrite the old stacks.
Should you want to append to the old stacks rather than overwrite them, use the option
./poor-mans-profiler.sh --elf=build/px4_fmu-v4_default/px4_fmu-v4_default.elf --nsamples=30000 --append
As one might suspect,
--nsamples=0 will instruct the script to only regenerate the SVG without accessing the target at all.
Please read the script for a more in depth understanding of how it works.