# Payloads and Cameras

PX4 supports a wide range of payloads and cameras.

Payloads are connected to Fight Controller outputs, and can generally be triggered automatically in missions, or manually using RC passthrough, mapping to a joystick, or MAVLink/MAVSDK commands.

注解

Payloads (actuators) can be tested in the pre-arm state, which disables motors but allows actuators to move. This may be safer than testing when the vehicle is armed.

# Mapping Drones

Mapping drones use cameras to capture images at time or distance intervals during surveys.

MAVLink cameras that support the MAVLink Camera Protocol (opens new window) provide the best integration with PX4 and QGroundControl. The MAVSDK provides simple APIs to use this protocol for both standalone camera operations (opens new window) and in missions (opens new window).

Cameras can also be connected directly to a flight controller using PWM or GPI outputs. PX4 supports the following set of MAVLink commands/mission items for cameras that are connected to the flight controller:

MAV_CMD_DO_SET_CAM_TRIGG_INTERVAL (opens new window) - set time interval between captures.
MAV_CMD_DO_SET_CAM_TRIGG_DIST (opens new window) - set distance between captures
MAV_CMD_DO_TRIGGER_CONTROL (opens new window) - start/stop capturing (using distance or time, as defined using above messages).

The following topics show how to connect and configure a camera:

Camera Triggering from flight controller PWM or GPIO outputs, or via MAVLink.
Camera Capture feedback via hotshoe input.

# Cargo Drones (Package Delivery)

Cargo drones commonly use grippers, winches, and other mechanisms to release packages at their destinations.

PX4 supports package delivery in missions using a gripper. Grippers can also be triggering using the MAV_CMD_DO_GRIPPER (opens new window) MAVLink command, or manually via a Joystick button.

For setup and usage information see:

注解

Support for winches and other release mechanisms is also intended.

If you need to perform cargo delivery using hardware that is not yet integrated, you can use Generic Actuator Control.

# Surveillance, Search & Rescue

Surveillance and Search & Rescue drones have similar requirements to mapping drones. The main differences are that, in addition to flying a planned survey area, they typically need good standalone control over the camera for image and video capture, and they may need to be able to work during both day and night

Use a camera that supports the MAVLink Camera Protocol (opens new window) as this supports image and video capture, zooming, storage management, multiple cameras on the same vehicle and switching between them, etc. These cameras can be controlled either manually from QGroundControl or via MAVSDK (for both standalone camera operations (opens new window) and in missions (opens new window)). See Camera triggering for information on how to configure your camera to work with MAVLink.

注解

Cameras connected directly to the flight controller only support camera triggering, and are unlikely to be suitable for most surveillance/search work.

A search and rescue drone may also need to carry cargo, for example, emergency supplies for a stranded hiker. See Cargo Drones above for information about payload delivery.

# Agricultural Drones/Crop Spraying

Agricultural drones are commonly used for mapping crop health and pest detection and animal management (herding, tracking, etc.). These cases are similar to the mapping and surveillance, search & rescue cases above. While specific crops/animals may need specialist cameras, the integration with PX4 is the same.

Agricultural drone may also be used for crop spraying. In this case the sprayer must be controlled as a generic actuator:

The Generic Actuator Control with MAVLink section explains how you can connect flight controller outputs to your sprayer so that they can be controlled using MAVLink. Most sprayers provide controls to activate/deactivate a pump; some also allow control over the rate of flow or the spray field (i.e. by controlling the nozzle shape, or using a spinner to distribute the payload).
You can define the area to spray using a Survey pattern (opens new window), or you can define the grid to fly using waypoints. In either case, it is important to ensure that the vehicle flight path and altitude provide adequate coverage for your particular spray being used.
You should add a "Set actuator" mission item to your mission before and after the survey pattern in order to enable and disable the sprayer.

# Generic Actuator Control

You can connect arbitrary hardware to unused PX4 outputs and control it using RC Control or MAVLink (either as commands or in a mission).

This is useful when you need to use a payload type for which there is no associated MAVLink command, or that is not supported by PX4.

注解

Prefer using integrated hardware and hardware-specific MAVLink commands to generic actuator control when possible. Using integrated hardware allows optimised mission planning and behaviour.

# Generic Actuator Control with MAVLink

MAV_CMD_DO_SET_ACTUATOR (opens new window) can be used to set the value of up to 6 actuators (at a time). This command can be used in missions by creating a "Set actuator" mission item, or as a stand alone command.

The outputs that are to be controlled are specified in the Actuators configuration screen by assigning the functions Offboard Actuator Set 1 to Offboard Actuator Set 6 to the desired actuator outputs.

Generic actuator output setting in QGC

MAV_CMD_DO_SET_ACTUATOR param1 to param6 control the outputs mapped by Offboard Actuator Set 1 to Offboard Actuator Set 6 respectively.

For example, in the image above, the AUX5 output is assigned the function Offboard Actuator Set 1 function. To control the actuator attached to AUX5 you would set the value of MAV_CMD_DO_SET_ACTUATOR.param1.

# Generic Actuator Control with RC

Up to 6 autopilot PWM or CAN outputs can be controlled using RC channels. The outputs that are to be controlled are specified in the Actuators configuration screen by assigning the functions RC AUX 1 to RC AUX 6 to the desired actuator outputs.

To map a particular RC channel to an output function RC AUX n (and hence it's assigned output) you use the RC_MAP_AUXn parameter that has the same n number.

For example, to control an actuator attached to AUX pin 3 (say) you would assign the output function RC AUX 5 to the output AUX3. You could then use set the RC channel to control the AUX3 output using RC_MAP_AUX5.

# Generic Actuator Control in Missions

To use generic actuator control in a mission you must first configure the outputs that you want to control using MAVLink.

Then in QGroundControl you can set the value of actuator outputs in a mission using the Set actuator mission item (this adds a MAV_CMD_DO_SET_ACTUATOR (opens new window) to the uploaded mission plan).

It is important to note that with generic actuator control, neither QGroundControl or PX4 know anything about the hardware being triggered. When processing the mission item, PX4 will simply set the outputs to the specified values and then immediately proceed to the next mission item. If the hardware requires time to activate and you need to pause at the current waypoint for this to happen, then you will need to plan the mission with additional items to achieve the desired behaviour.

注解

This is one reason why integrated hardware is preferred! It allows missions to be written generically, with any hardware-specific behaviour or timing managed by the flight stack configuration.

To use a generic actuator in a mission:

Create a waypoint mission item where you want the actuator command.
Change the waypoint mission item to a "Set actuator" mission item:
- Select the header on the waypoint mission editor to open the Select Mission Command editor.
- Select the category Advanced, and then the Set actuator item (if the item is not present, try a more recent version of QGroundControl or a daily build). This will change the mission item type to "Set actuator".
Select the actuators that are connected and set their values (these are normalized between -1 and 1).

# MAVSDK (Example script)

The following MAVSDK (opens new window) example code (opens new window) shows how to trigger payload release using the MAVSDK Action plugin's set_actuator() (opens new window) method.

The set_actuator() index values map to the MAVLink payload outputs defined for your airframe.

MAVSDK

sends the MAV_CMD_DO_SET_ACTUATOR (opens new window) MAVLink command under the hood.

#include <mavsdk/mavsdk.h>
#include <mavsdk/plugins/action/action.h>
#include <chrono>
#include <cstdint>
#include <iostream>
#include <future>

using namespace mavsdk;

void usage(const std::string& bin_name)
{
    std::cerr << "Usage :" << bin_name << " <connection_url> <actuator_index> <actuator_value>\n"
              << "Connection URL format should be :\n"
              << " For TCP : tcp://[server_host][:server_port]\n"
              << " For UDP : udp://[bind_host][:bind_port]\n"
              << " For Serial : serial:///path/to/serial/dev[:baudrate]\n"
              << "For example, to connect to the simulator use URL: udp://:14540\n";
}

int main(int argc, char** argv)
{
    if (argc != 4) {
        usage(argv[0]);
        return 1;
    }

    const std::string connection_url = argv[1];
    const int index = std::stod(argv[2]);
    const float value = std::stof(argv[3]);

    Mavsdk mavsdk;
    const ConnectionResult connection_result = mavsdk.add_any_connection(connection_url);

    if (connection_result != ConnectionResult::Success) {
        std::cerr << "Connection failed: " << connection_result << '\n';
        return 1;
    }

    std::cout << "Waiting to discover system...\n";
    auto prom = std::promise<std::shared_ptr<System>>{};
    auto fut = prom.get_future();

    // We wait for new systems to be discovered, once we find one that has an
    // autopilot, we decide to use it.
    mavsdk.subscribe_on_new_system([&mavsdk, &prom]() {
        auto system = mavsdk.systems().back();

        if (system->has_autopilot()) {
            std::cout << "Discovered autopilot\n";

            // Unsubscribe again as we only want to find one system.
            mavsdk.subscribe_on_new_system(nullptr);
            prom.set_value(system);
        }
    });

    // We usually receive heartbeats at 1Hz, therefore we should find a
    // system after around 3 seconds max, surely.
    if (fut.wait_for(std::chrono::seconds(3)) == std::future_status::timeout) {
        std::cerr << "No autopilot found, exiting.\n";
        return 1;
    }

    // Get discovered system now.
    auto system = fut.get();

    // Instantiate plugins.
    auto action = Action{system};

    std::cout << "Setting actuator...\n";
    const Action::Result set_actuator_result = action.set_actuator(index, value);

    if (set_actuator_result != Action::Result::Success) {
        std::cerr << "Setting actuator failed:" << set_actuator_result << '\n';
        return 1;
    }

    return 0;
}

← 飞行前检查飞行报告 →