PX4 User Guide (v1.12)

# Bootloader Update

The PX4 bootloader (opens new window) is used to load firmware for Pixhawk boards (PX4FMU, PX4IO) and PX4FLOW.

This topic explains several methods for updating the Pixhawk bootloader.

Note

Hardware usually comes with an appropriate bootloader version pre-installed. A case where you may need to update is newer Pixhawk boards that install FMUv2 firmware: Firmware > FMUv2 Bootloader Update.

# Building the new PX4 bootloader yourself

Boards starting with FMUv6X (STM32H7) use the in-tree PX4 bootloader. Older boards use the bootloader from the legacy PX4 bootloader (opens new window) repository. Please refer to the instructions in the README to learn how to use it.

Build the new bootloader in the PX4-Autopilot folder with:

make px4_fmu-v6x_bootloader

Which will build the bootloader binary as build/px4_fmu-v6x_bootloader/px4_fmu-v6x_bootloader.elf which can be flashed via SWD or DFU. If you are building the bootloader you should be familiar with one of these options already.

If you need a HEX file instead of an ELF file, use objcopy:

arm-none-eabi-objcopy -O ihex build/px4_fmu-v6x_bootloader/px4_fmu-v6x_bootloader.elf px4_fmu-v6x_bootloader.hex

# QGroundControl Bootloader Update

The easiest approach is to first use QGroundControl to install firmware with the desired/latest bootloader. You can then initiate bootloader update on next restart by setting the parameter: SYS_BL_UPDATE.

Note

This approach can only be used if SYS_BL_UPDATE is present in firmware (currently just FMUv2 and some custom firmware).

The steps are:

  1. Insert an SD card (enables boot logging to debug any problems).

  2. Update the Firmware with an image containing the new/desired bootloader.

    Note

    The updated bootloader might be supplied in custom firmware (i.e. from the dev team), or it or may be included in the latest master.

    FMUv2 update

  3. Wait for the vehicle to reboot.

  4. Find and enable the parameter SYS_BL_UPDATE.

  5. Reboot (disconnect/reconnect the board). The bootloader update will only take a few seconds.

Generally at this point you may then want to update the firmware again using the correct/newly installed bootloader.

# Dronecode Probe Bootloader Update

The following steps explain how you can "manually" update the bootloader using the dronecode probe:

  1. Get a binary containing the bootloader (either from dev team or build it yourself).

  2. Connect the Dronecode probe to your PC via USB.

  3. Go into the directory containing the binary and run the following command in the terminal:

    arm-none-eabi-gdb px4fmuv5_bl.elf

  4. The gdb terminal appears and it should display the following output:

    GNU gdb (GNU Tools for Arm Embedded Processors 7-2017-q4-major) 8.0.50.20171128-git
Copyright (C) 2017 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.  Type "show copying"
and "show warranty" for details.
This GDB was configured as "--host=x86_64-linux-gnu --target=arm-none-eabi".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>.
Find the GDB manual and other documentation resources online at:
<http://www.gnu.org/software/gdb/documentation/>.
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from px4fmuv5_bl.elf...done.

  5. Find your <dronecode-probe-id> by running an ls command in the /dev/serial/by-id directory.

  6. Now connect to the Dronecode probe with the following command:

    tar ext /dev/serial/by-id/<dronecode-probe-id>

  7. Power on the Pixhawk with another USB cable and connect the Dronecode probe to the FMU-DEBUG port.

    Note

    To be able to connect the Dronecode probe to the FMU-DEBUG port, you may need to remove the case (e.g. on Pixhawk 4 you would do this using a T6 Torx screwdriver).

  8. Use the following command to scan for the Pixhawk’s swd and connect to it:

    (gdb) mon swdp_scan
(gdb) attach 1

  9. Load the binary into the Pixhawk:

    (gdb) load

After the bootloader has updated you can Load PX4 Firmware using QGroundControl.

# Other Boards (Non-Pixhawk)

Boards that are not part of the Pixhawk Series will have their own mechanisms for bootloader update.

For boards that are preflashed with Betaflight, see Bootloader Flashing onto Betaflight Systems.

← Bootloader Flashing onto Betaflight Systems →