PX4 User Guide (v1.13)

# Crazyflie 2.0 (Discontinued)

WARNING

Crazyflie 2.0 has been discontinued/superseded. Try Bitcraze Crazyflie 2.1 instead!

WARNING

The Crazyflie line of micro quads was created by Bitcraze AB. An overview of the Crazyflie 2.0 can be found here (opens new window).

Crazyflie2 Image

# Quick Summary

Note

The main hardware documentation is here: https://wiki.bitcraze.io/projects:crazyflie2:index

  • Main System-on-Chip: STM32F405RG
    • CPU: 168 MHz ARM Cortex M4 with single-precision FPU
    • RAM: 192 KB SRAM
  • nRF51822 radio and power management MCU
  • MPU9250 Accel / Gyro / Mag
  • LPS25H barometer

# Where to Buy

# Flashing PX4

After setting up the PX4 development environment, follow these steps to install the PX4 Autopilot on the Crazyflie 2.0:

  1. Download the source code of the PX4 Bootloader:

    git clone https://github.com/PX4/Bootloader.git

  2. Navigate into the top directory of the source code and compile it using:

    make crazyflie_bl

  3. Put the Crazyflie 2.0 into DFU mode by following these steps:

    • Ensure it is initially unpowered.
    • Hold down the reset button (see figure below...). Crazyflie2 Reset Button
    • Plug into computer's USB port.
    • After a second, the blue LED should start blinking and after 5 seconds should start blinking faster.
    • Release button.

  4. Install dfu-util:

    sudo apt-get update
sudo apt-get install dfu-util

  5. Flash bootloader using dfu-util and unplug Crazyflie 2.0 when done:

    sudo dfu-util -d 0483:df11 -a 0 -s 0x08000000 -D ./build/crazyflie_bl/crazyflie_bl.bin

    When powering on the Crazyflie 2.0 the yellow LED should blink.

  6. Download the source code of the PX4 autopilot:

    git clone https://github.com/PX4/PX4-Autopilot.git

  7. Navigate into the top directory of the source code and compile it using:

    make bitcraze_crazyflie_default upload

  8. When prompted to plug in device, plug in Crazyflie 2.0. The yellow LED should start blinking indicating bootloader mode. Then the red LED should turn on indicating that the flashing process has started.

  9. Wait for completion.

  10. Done! Calibrate the sensors using QGroundControl (opens new window).

Note

If QGroundControl does not connect with the vehicle, ensure that in nuttx-config (opens new window) for crazyflie # CONFIG_DEV_LOWCONSOLE is not set is replaced by CONFIG_DEV_LOWCONSOLE=y. This should be done using menuconfig:

make bitcraze_crazyflie_default menuconfig

or qconfig (Check Low-level console support under Serial Driver Support in GUI):

make bitcraze_crazyflie_default qconfig

# Wireless Setup Instructions

The onboard nRF module allows connecting to the board via Bluetooth or through the proprietary 2.4GHz Nordic ESB protocol.

Using the official Bitcraze Crazyflie phone app:

  • Connect via Bluetooth.
  • Change mode in settings to 1 or 2.
  • Calibrate via QGroundControl.

Connecting via MAVLink:

  • Use a Crazyradio PA alongside a compatible GCS.
  • Download the crazyflie-lib-python source code:
    git clone https://github.com/bitcraze/crazyflie-lib-python.git

Note

We will use cfbridge.py (opens new window) to setup a wireless MAVlink communication link between Crazyflie 2.0 (flashed with PX4) and QGroundControl. Cfbridge enables QGroundControl to communicate with the crazyradio PA. The C based cfbridge (opens new window) is currently experiencing data loss issues, which is why we have chosen to use cfbridge.py.

  • Make sure you have set the udev permissions to use the USB Radio. To do this, follow the steps listed here (opens new window) and restart your computer.
  • Connect a Crazyradio PA via USB.
  • Build a virtual environment (local python environment) (opens new window) with package dependencies using the following method:
    pip install tox --user
  • Navigate to the crazyflie-lib-python folder and type:
    make venv
  • Activate the virtual environment:
    source venv-cflib/bin/activate
  • Install required dependencies:
    pip install -r requirements.txt --user

To connect Crazyflie 2.0 with crazyradio, launch cfbridge by following these steps:

  • Power off and power on Crazyflie 2.0 and wait for it to boot up.

  • Connect a Crazyflie radio device via USB.

  • Navigate to the crazyflie-lib-python folder.

  • Activate the environment:

    source venv-cflib/bin/activate

  • Navigate to the examples folder:

    cd examples

  • Launch cfbridge:

    python cfbridge.py

    Note

    Cfbridge by default tries to initiate the radio link communication on channel 80 and with crazyflie address 0xE7E7E7E7E7. If you are using multiple crazyflies and/or crazyradios (opens new window) in the same room and want to use a different channel and/or address for each, first connect the crazyflie with QGroundControl via a USB cable and change the syslink parameters (channel, address) in QGroundControl. Next, launch the cfbridge by giving the same channel and address as the first and second arguments respectively, e.g: python cfbridge.py 90 0x0202020202

  • Open QGroundControl.

  • After using cfbridge, you can deactivate the virtualenv if you activated it by pressing CTRL+z. Most of the time, launching cfbridge again from the same terminal doesn't connect to crazyflie, this can be solved by closing the terminal and relaunching cfbridge in a new terminal.

TIP

If you change any driver in crazyflie-lib-python (opens new window) or if launching cfbridge in a new terminal does not find crazyflie, you can try navigating to the crazyflie-lib-python folder and run the script below to rebuild cflib.

make venv

Note

To use Joystick, set COM_RC_IN_MODE in QGroundControl to "Joystick/No RC Checks". Calibrate the Joystick and set the Joystick message frequency in QGroundControl to any value between 5 to 14 Hz (10 Hz is recommended). To be able to set the frequency, the advanced option should be enabled. This is the rate at which Joystick commands are sent from QGroundControl to Crazyflie 2.0 (to do this, you will need to follow the instructions here (opens new window) to obtain the latest QGroundControl source code (master) and build it).

# Hardware Setup

Crazyflie 2.0 is able to fly with precise control in Stabilized mode, Altitude mode and Position mode.

  • You will need the Z-ranger deck (opens new window) to fly in Altitude mode. If you also want to fly in the Position mode, it is recommended you buy the Flow deck (opens new window) which also has the integrated Z-ranger sensor.
  • The onboard barometer is highly susceptible to any external wind disturbances including those created by Crazyflie's own propellers. Hence, we isolated the barometer with a piece of foam, and then mounted the distance sensor on top of it as shown below:

Crazyflie barometer

Crazyflie barometer foam

Crazyflie optical flow

In order to log flight details, you can mount SD card deck on top of crazyflie as shown below:

Crazyflie SDCard

Then, you need to stick the battery on top of the SD card deck using a double sided tape:

Crazyflie battery setup

# Altitude Control

Crazyflie is able to fly in Altitude mode if you use a Z-ranger deck (opens new window). According to the datasheet, the maximum height (above ground) the range finder can sense is 2 m. However, when tested on dark surfaces this value decreases to 0.5 m. On a light floor, it goes up to max 1.3 m. This means you cannot hold altitudes above this value in Altitude or Position flight modes.

TIP

If the Crazyflie 2.0 height drifts at mid-throttle command in Altitude mode or Position mode, first try rebooting the vehicle. If this does not fix the problem, recalibrate the accel and mag (compass).

Note

Since the onboard barometer is highly susceptible to wind disturbances created by the Crazyflie's own propellers, you cannot rely on it to hold altitude.

# Position Control

With Flow deck (opens new window), you can fly Crazyflie 2.0 in Position mode. Unlike PX4flow, the flow deck does not house a gyro, hence the onboard gyro is used for flow fusion to find the local position estimates. Moreover, the flow deck shares the same SPI bus as the SD card deck, therefore logging at high rate on SD card is not recommended when flying in Position mode.

Note

A ulog for flight in Position mode is available here (opens new window). This can be used as a reference to compare your flight performance.

# Using FrSky Taranis RC Transmitter as Joystick

If you already own a Taranis RC transmitter and want to use it as a controller, it can be configured as a USB Joystick:

  • Create a new model in Taranis.

    Taranis - new model

  • In MODEL SETUP menu page, turn off both internal and external TX modules.

    Taranis - model setup

  • In OUTPUTS menu page (also called “SERVOS” page in some Taranis transmitters), invert Throttle (CH1) and Aileron (CH3).

    Taranis - outputs

To use Taranis switches to arm/disarm and switch to different flight modes:

  • In Taranis UI MIXER menu page, you can assign the switches to any channel in the range channel 9-16 which map to the buttons 0-7 in the QGroundControl Joystick setup. For example, Taranis “SD” switch can be set to channel 9 in Taranis UI:

    Taranis switch setup

  • Connect Taranis to PC with a USB cable and Open QGroundControl.

  • In QGroundControl Joystick Setup, you can see the buttons turning yellow when you switch them on. For example, channel 9 in Taranis maps to button 0 in QGroundControl Joystick setup. You can assign any mode to this button e.g. Altitude mode. Now when you lower the switch "SD", flight mode will change to Altitude.

    Joystick setup

# ROS

To connect to Crazyflie 2.0 via MAVROS:

  • Start up cfbridge using the above instructions.
  • Change the UDP port QGroundControl listens to:
    • In QGroundControl, navigate to Application Settings > General and uncheck all the boxes under Autoconnect to the following devices.
    • Add in Comm Links a link of type UDP, check the Automatically Connect on Start option, change the Listening Port to 14557, add Target Hosts: 127.0.0.1 and then press OK.
  • Make sure you have MAVROS (opens new window) installed.
  • Start MAVROS with command:
    roslaunch mavros px4.launch fcu_url:="udp://:14550@127.0.0.1:14551" gcs_url:="udp://@127.0.0.1:14557"
  • Restart QGroundControl if it doesn't connect.

# Flying

← Aerotenna OcPoC-Zynq Mini →