# PX4 Bootloader Flashing onto Betaflight Systems
This page documents how to flash the PX4 bootloader onto boards that are already flashed with Betaflight (e.g. OmnibusF4 SD or Kakute F7).
There are three tools that can be used to flash the PX4 bootloader: Betaflight Configurator, dfu-util (opens new window) command line tool, or the graphical dfuse (opens new window) (Windows only).
注解
The Betaflight Configurator is easiest, but newer versions may not support non-betaflight bootloader update. You might try it first, but use the other methods if firmware update does not work. 飞控板上电后可以放开该按钮。
# Betaflight Configurator Bootloader Update
注解
Betaflight Configurator may not support PX4 Bootloader update, as of May 2023. Older versions should work, though the precise versions are not known. 飞控板上电后可以放开该按钮。
To install the PX4 bootloader using the Betaflight Configurator:
- Download or build bootloader firmware for the board you want to flash.
- 下载适用于您平台的 Betaflight 配置器 (opens new window)。
提示
If using the Chrome web browser, a simple cross-platform alternative is to install the configurator as an extension from here (opens new window). 飞控板上电后可以放开该按钮。
- 将飞控板连接到 PC 并启动 Betaflight 配置器。
- Press the Load Firmware [Local] button
- 从文件系统中选择 bootloader 二进制文件，然后烧写进飞控板的 flash。
现在，您应当可以在飞控板上安装 PX4 固件了。
# DFU Bootloader Update
This section explains how to flash the PX4 bootloader using the dfu-util (opens new window) or the graphical dfuse (opens new window) tool (Windows only).
You will first need to download or build bootloader firmware for the board you want to flash (below, this is referred to as <target.bin>).
注解
All of the methods below are safe as the STM32 MCU cannot be bricked! DFU 不会被烧写覆盖，并且总是允许安装新固件，即便烧写失败。 飞控板上电后可以放开该按钮。
# DFU mode
Both tools require the board to be in DFU mode. 要进入 DFU 模式， 当将 USB 连接到电脑时按住启动按钮。 The button can be released after the board has powered up.
# dfu-util
注解
The Holybro Kakute H7 v2 and mini flight controllers may require that you first run an additional command to erase flash parameters (in order to fix problems with parameter saving):
dfu-util -a 0 --dfuse-address 0x08000000:force:mass-erase:leave -D build/<target>/<target>.bin
The command may generate an error which can be ignored. Once completed, enter DFU mode again to complete the regular flashing. 飞控板上电后可以放开该按钮。
To flash the bootloader onto the flight controller:
dfu-util -a 0 --dfuse-address 0x08000000 -D build/<target>/<target>.bin
重新启动飞控板，并且不要按下启动按钮。
# dfuse
The dfuse manual can be found here: https://www.st.com/resource/en/user_manual/cd00155676.pdf
Use the tool to flash the <target>.bin file.
# Bootloader Firmware
The tools above flash pre-built bootloader firmware. Bootloader firmware can be built for most targets using the normal PX4 source code, while other targets can only be build using source in the bootloader repository.
Flight controllers that have bootloader PX4-Autopilot make targets, can build the bootloader from the PX4-Autopilot source. The list of controllers for which this applies can be obtained by running the following make command, and noting the make targets that end in _bootloader
$make list_config_targets
...
cuav_nora_bootloader
cuav_x7pro_bootloader
cubepilot_cubeorange_bootloader
holybro_durandal-v1_bootloader
holybro_kakuteh7_bootloader
holybro_kakuteh7v2_bootloader
holybro_kakuteh7mini_bootloader
matek_h743-mini_bootloader
matek_h743-slim_bootloader
modalai_fc-v2_bootloader
mro_ctrl-zero-classic_bootloader
mro_ctrl-zero-h7_bootloader
mro_ctrl-zero-h7-oem_bootloader
mro_pixracerpro_bootloader
px4_fmu-v6u_bootloader
px4_fmu-v6x_bootloader
To build for these flight controllers, download and build the PX4-Autopilot source (opens new window), and then make the target using the following commands:
git clone --recursive https://github.com/PX4/PX4-Autopilot.git
cd PX4-Autopilot
make <target> # For example: holybro_kakuteh7mini_bootloader
For other flight controllers download the PX4/Bootloader (opens new window) repository and build the source code using the appropriate targets:
git clone --recursive https://github.com/PX4/Bootloader.git
cd Bootloader
make <target> # For example: omnibusf4sd_bl or kakutef7_bl
# 重新安装 Beatflight 固件
In order to switch back to Betaflight:
- Backup the PX4 parameters. You can do this by exporting them to an SD card.
- Keep the bootloader button pressed while attaching the USB cable
- Flash Betaflight as usual with the Betaflight-configurator