# 비행 중단 설정

비행 중단 안전 장치는 안전 점검</1>(예. 기체 유형과 비행 모드가 무엇이든 RC 연결 끊김, geofence를 벗어남 등이 발생할 때)또는 Failure Detector에 의해 작동합니다.

Note

Flight termination may also be triggered from a ground station or companion computer using the MAVLink MAV_CMD_DO_FLIGHTTERMINATION (opens new window) command. This is sent, for example, when you call the MAVSDK Action plugin (opens new window) terminate() or terminate_async() methods.

연결된 장치에 따라 PWM 안전장치 출력은 아래와 같이 활용할 수 있습니다.

Depending on what devices are connected, the PWM failsafe outputs can be used to:

  • 낙하산 펼치기.
  • 랜딩기어 펼치기.
  • 카메라를 보호하기 위해 PWM방식으로 연결된 짐벌을 안전 각도(또는 수납 위치) 로 움직이기.
  • 에어백 같은 팽창 장비 가동하기.
  • 알람 울리기.

PX4는 어떤 안전 장치가 장착되어 있는지 알지 못합니다. 미리 정의된 PWM 값 세트를 출력에 적용하기만 하면 됩니다. After triggering you should unplug the battery as soon as possible. You will need to reboot/power cycle the vehicle before it can be used again.

TIP

Failsafe 값은 종료시 모든 출력에 적용됩니다. 모터 또는 특정 안전 장치의 독립적인 시간 기반 (또는 기타) 트리거링을 구성하는 방법은 없습니다.

Note

이것은 독립적인 항공 종료 시스템아닙니다. 전원이 끊기거나 자동조종장치가 완전히 충돌하면 안전 장치가 작동하지 않습니다.

Note

This is not an independent Flight Termination System. If power is lost or if the autopilot crashes completely, the failsafe devices will not be triggered.

# 하드웨어 설정

Any safety device(s) (e.g. a parachute) that can be triggered by changing a PWM value can be used, and may be connected to any free PWM port (both MAIN and AUX).

Note

If you're using Pixhawk-series board you will have to separately power the servo rail (i.e. from a 5V BEC, which is often also available from your ESC).

# 소프트웨어 설정

The Safety topic explains how to set the flight termination as the failsafe action to be performed for particular failsafe check.

마지막으로, 다른 모터에 대해 PWM_AUX_FAILnPWM_MAIN_FAILn의 PWM 값을 설정하십시오.

  • CBRK_FLIGHTTERM=0을 설정하여 고장 감지기를 활성화하십시오.
  • Safety > Failure Detector > Attitude Trigger비행 중단을 시작하는 한계 attitude를 구성하는 방법을 설명합니다. 참고 이륙중의 과한 attitude는 비행 중단 대신 lockdown(모터를 정지시키지만 낙하산을 발사하지 않음)을 시작합니다. lockdown은 CBRK_FLIGHTTERM의 값에 관계없이 항상 활성화됩니다. 모터 또는 특정 안전 장치의 독립적인 시간 기반 (또는 기타) 트리거링을 구성하는 방법은 없습니다.
  • Safety > External Automatic Trigger System (ATS)은 외부 트리거 시스템을 설정하는 방법에 대해 설명합니다.

아래의 다이어그램은 비행 중단과 관련된 논리적 흐름을 보여 줍니다.

마지막으로, 모든 모터에 대해 PWM_AUX_FAILnPWM_MAIN_FAILn PWM 값을 설정합니다.

아래의 다이어그램은 비행 중단과 관련된 논리적 흐름을 나타냅니다.

# 로직 다이어그램

The diagram below shows the logical flow around flight termination.

Logic diagram