# 시리얼 포트 매핑

This topic shows how to determine the mapping between USART/UART serial port device names (e.g. "ttyS0") and the associated ports on a flight controller, such as TELEM1, TELEM2, GPS1, RC SBUS, Debug console.

The instructions are used to generate serial port mapping tables in flight controller documentation. 예: Pixhawk 4 > 직렬 포트 매핑.

Note

The function assigned to each port does not have to match the name (in most cases), and is set using a Serial Port Configuration. Usually the port function is configured to match the name, which is why the port labelled GPS1 will work with a GPS out of the box.

# STMxxyyy의 NuttX

보드 설정 파일을 검사하여 STMxxyyy 아키텍처에서 NuttX 빌드에 대한 매핑 획득 방법을 설명합니다. FMUv5를 사용하지만, 다른 FMU 버전/NuttX 보드에도 유사하게 확장할 수 있습니다.

# default.cmake

default.cmake는 여러 직렬 포트 매핑을 나열합니다(텍스트 "SERIAL_PORTS" 검색).

/boards/px4/fmu-v5/default.cmake (opens new window)에서:

SERIAL_PORTS
    GPS1:/dev/ttyS0
    TEL1:/dev/ttyS1
    TEL2:/dev/ttyS2
    TEL4:/dev/ttyS3

Alternatively you can launch boardconfig using make px4_fmu-v5 boardconfig and access the serial port menu

    CONFIG_STM32F7_UART4=y
CONFIG_STM32F7_UART7=y
CONFIG_STM32F7_UART8=y
CONFIG_STM32F7_USART1=y
CONFIG_STM32F7_USART2=y
CONFIG_STM32F7_USART3=y
CONFIG_STM32F7_USART6=y

# nsh/defconfig

The nsh/defconfig allows you to determine which ports are defined, whether they are UART or USARTs, and the mapping between USART/UART and device. You can also determine which port is used for the serial/debug console.

Open the board's defconfig file, for example: /boards/px4/fmu-v5/nuttx-config/nsh/defconfig (opens new window)

Search for the text "ART" until you find a section like with entries formatted like CONFIG_STM32xx_USARTn=y (where xx is a processor type and n is a port number). For example:

ttyS0 CONFIG_STM32F7_USART1=y
ttyS1 CONFIG_STM32F7_USART2=y
ttyS2 CONFIG_STM32F7_USART3=y
ttyS3 CONFIG_STM32F7_UART4=y
ttyS4 CONFIG_STM32F7_USART6=y
ttyS5 CONFIG_STM32F7_UART7=y
ttyS6 CONFIG_STM32F7_UART8=y

The entries tell you which ports are defined, and whether they are UART or USART.

DEBUG 콘솔 매핑을 가져오기 위해 SERIAL_CONSOLE에 대한 defconfig 파일 (opens new window)을 검색합니다. 아래에서 콘솔이 UART7에 있음을 알 수 있습니다.

CONFIG_UART7_SERIAL_CONSOLE=y

To get the DEBUG console mapping we search the defconfig file (opens new window) for SERIAL_CONSOLE. Below we see that the console is on UART7:

#define PX4IO_SERIAL_DEVICE            "/dev/ttyS6"
#define PX4IO_SERIAL_TX_GPIO           GPIO_UART8_TX
#define PX4IO_SERIAL_RX_GPIO           GPIO_UART8_RX
#define PX4IO_SERIAL_BASE              STM32_UART8_BASE

# board_config.h

예: /boards/px4/fmu-v5/src/board_config.h (opens new window)

따라서 PX4IO는 ttyS6에 있습니다(이전 섹션에서 이미 알고 있는 UART8에 매핑되는 것도 볼 수 있습니다).

ttyS0 CONFIG_STM32F7_USART1=y GPS1
ttyS1 CONFIG_STM32F7_USART2=y TEL1
ttyS2 CONFIG_STM32F7_USART3=y TEL2
ttyS3 CONFIG_STM32F7_UART4=y TEL4
ttyS4 CONFIG_STM32F7_USART6=y
ttyS5 CONFIG_STM32F7_UART7=y DEBUG
ttyS6 CONFIG_STM32F7_UART8=y PX4IO

최종 매핑은 다음과 같습니다.

# 결합

비행 콘트롤러 문서의 결과 표는 다음과 같습니다.

ttyS0 CONFIG_STM32F7_USART1=y GPS1
ttyS1 CONFIG_STM32F7_USART2=y TEL1
ttyS2 CONFIG_STM32F7_USART3=y TEL2
ttyS3 CONFIG_STM32F7_UART4=y TEL4
ttyS4 CONFIG_STM32F7_USART6=y
ttyS5 CONFIG_STM32F7_UART7=y DEBUG
ttyS6 CONFIG_STM32F7_UART8=y PX4IO

In the flight controller docs the resulting table is:

UART 장치 포트
UART1 /dev/ttyS0 GPS
USART2 /dev/ttyS1 TELEM1 (흐름 제어)
USART3 /dev/ttyS2 TELEM2 (흐름 제어)
UART4 /dev/ttyS3 TELEM4
USART6 /dev/ttyS4 RC SBUS
UART7 /dev/ttyS5 디버그 콘솔
UART8 /dev/ttyS6 PX4IO

# 기타 아키텍처

Note

Contributions welcome!

# See Also