Skip to content

Holybro Pix32 v6

WARNING

PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues.

Pix32 v6® is the latest update to the pix32 v5 flight controllers. It is a variant of the Pixhawk 6C with a modular design and shares the same FMUv6C Target. It is comprised of a separate flight controller and carrier board which are connected by a 100 pin connector. It is designed for those pilots who need a high power, flexible and customizable flight control system.

It is equipped with a high performance H7 Processor, and comes with IMU redundancy, temperature-controlled IMU board, and cost effective design, delivering incredible performance and reliability. It complies with the Connector Standard.

Introduction

Inside the Pix32 v6, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.

The Pix32 v6’s H7 MCU contain the Arm® Cortex®-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models. It includes high-performance, low-noise IMUs on board, designed to be cost effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances.

This flight controller is perfect for people that is looking for a affordable and modular flight controller that can use a customized baseboard. We have made the pix32 v6 base board schematics public, you can either make a custom carrier board yourself or just let us help you with it. By using a customize baseboard, you can make sure that the physical size, pinouts and power distribution requirements match your vehicle perfectly, ensuring that you have all the connections you need and none of the expense and bulk of connectors you don’t.

Key Design Points

  • High performance STM32H743 Processor with more computing power & RAM
  • New cost-effective design with low-profile form factor
  • Integrated vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
  • IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs

Technical Specification

Processors & Sensors

  • FMU Processor: STM32H743
    • 32 Bit Arm® Cortex®-M7, 480MHz, 2MB memory, 1MB SRAM
  • IO Processor: STM32F103
    • 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
  • On-board sensors
    • Accel/Gyro: ICM-42688-P
    • Accel/Gyro: BMI055
    • Mag: IST8310
    • Barometer: MS5611

Electrical data

  • Voltage Ratings:
    • Max input voltage: 6V
    • USB Power Input: 4.75~5.25V
    • Servo Rail Input: 0~36V
  • Current Ratings:
    • TELEM1 Max output current limiter: 1.5A
    • All other port combined output current limiter: 1.5A

Mechanical data

  • FC Module Dimensions: 44.8 x 44.8 x 13.5
  • FC Module Weight: 36g

Interfaces

  • 16- PWM servo outputs (8 from IO, 8 from FMU)

  • 3 general purpose serial ports

    • TELEM1 - Full flow control, separate 1.5A current limit
    • TELEM2 - Full flow control
    • TELEM3
  • 2 GPS ports

    • GPS1 - Full GPS port (GPS plus safety switch)
    • GPS2 - Basic GPS port
  • 1 I2C port

    • Supports dedicated I2C calibration EEPROM located on sensor module
  • 2 CAN Buses

    • CAN Bus has individual silent controls or ESC RX-MUX control
  • 2 Debug ports:

    • FMU Debug
    • I/O Debug
  • Dedicated R/C input for Spektrum / DSM and S.BUS, CPPM, analog / PWM RSSI

  • Dedicated S.BUS output

  • 2 Power input ports (Analog)

  • Other Characteristics:

    • Operating & storage temperature: -40 ~ 85°c

Where to Buy

Order from Holybro.

Pinouts

Serial Port Mapping

UARTDevicePort
USART1/dev/ttyS0GPS1
USART2/dev/ttyS1TELEM3
USART3/dev/ttyS2Debug Console
UART5/dev/ttyS3TELEM2
USART6/dev/ttyS4PX4IO
UART7/dev/ttyS5TELEM1
UART8/dev/ttyS6GPS2

Dimensions

Voltage Ratings

Pix32 v6 can be triple-redundant on the power supply if three power sources are supplied. The three power rails are: USB, POWER1, POWER2 (N/A on Pix32 v6 Mini-Baseboard) .

Normal Operation Maximum Ratings

Under these conditions all power sources will be used in this order to power the system:

  1. POWER1 and POWER2 inputs (4.9V to 5.5V)
  2. USB input (4.75V to 5.25V)

Absolute Maximum Ratings

Under these conditions the system will not draw any power (will not be operational), but will remain intact.

  1. POWER1 and POWER2 inputs (operational range 4.1V to 5.7V, 0V to 10V undamaged)
  2. USB input (operational range 4.1V to 5.7V, 0V to 6V undamaged)
  3. Servo input: VDD_SERVO pin of FMU PWM OUT and I/O PWM OUT (0V to 42V undamaged)

Voltage monitoring

Pix32 v6 uses analog power modules.

Holybro makes various analog power modules for different need.

Building Firmware

TIP

Most users will not need to build this firmware! It is pre-built and automatically installed by QGroundControl when appropriate hardware is connected.

To build PX4 for this target:

make px4_fmu-v6c_default

Debug Port

The PX4 System Console and SWD interface run on the FMU Debug port.

The pinouts and connector comply with the Pixhawk Debug Full interface defined in the Pixhawk Connector Standard interface (JST SM10B connector).

PinSignalVolt
1 (red)Vtref+3.3V
2 (blk)Console TX (OUT)+3.3V
3 (blk)Console RX (IN)+3.3V
4 (blk)SWDIO+3.3V
5 (blk)SWCLK+3.3V
6 (blk)SWO+3.3V
7 (blk)NFC GPIO+3.3V
8 (blk)PH11+3.3V
9 (blk)nRST+3.3V
10 (blk)GNDGND

For information about using this port see:

Peripherals

Supported Platforms / Airframes

Any multicopter / airplane / rover or boat that can be controlled with normal RC servos or Futaba S-Bus servos. The complete set of supported configurations can be seen in the Airframes Reference.

Further info