Modules Reference: Magnetometer (Driver)
ak09916
Source: drivers/magnetometer/akm/ak09916
使用
ak09916 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 12
[-R <val>] Rotation
default: 0
stop
status print status infoak8963
Source: drivers/magnetometer/akm/ak8963
使用
ak8963 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 12
[-R <val>] Rotation
default: 0
stop
status print status infobmm150
Source: drivers/magnetometer/bosch/bmm150
使用
bmm150 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 16
[-R <val>] Rotation
default: 0
stop
status print status infohmc5883
Source: drivers/magnetometer/hmc5883
使用
hmc5883 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
[-T] Enable temperature compensation
stop
status print status infoiis2mdc
Source: drivers/magnetometer/st/iis2mdc
使用
iis2mdc <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 48
stop
status print status infoist8308
Source: drivers/magnetometer/isentek/ist8308
使用
ist8308 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 12
[-R <val>] Rotation
default: 0
stop
status print status infoist8310
Source: drivers/magnetometer/isentek/ist8310
使用
ist8310 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 14
[-R <val>] Rotation
default: 0
stop
status print status infolis2mdl
Source: drivers/magnetometer/lis2mdl
使用
lis2mdl <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 30
[-R <val>] Rotation
default: 0
stop
status print status infolis3mdl
Source: drivers/magnetometer/lis3mdl
使用
lis3mdl <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 30
[-R <val>] Rotation
default: 0
reset
stop
status print status infolsm9ds1_mag
Source: drivers/magnetometer/lsm9ds1_mag
使用
lsm9ds1_mag <command> [arguments...]
Commands:
start
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
stop
status print status infommc5983ma
Source: drivers/magnetometer/memsic/mmc5983ma
使用
mmc5983ma <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 48
reset
stop
status print status infoqmc5883l
Source: drivers/magnetometer/qmc5883l
Usage
qmc5883l <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 13
[-R <val>] Rotation
default: 0
stop
status print status inform3100
Source: drivers/magnetometer/rm3100
Usage
rm3100 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
stop
status print status infovcm1193l
Source: drivers/magnetometer/vtrantech/vcm1193l
Usage
vcm1193l <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
stop
status print status info