PX4 Guide (v1.15)

中文 (Chinese)

English
한국어 (Korean)
Мови (Ukrainian)

中文 (Chinese)

English
한국어 (Korean)
Мови (Ukrainian)

Appearance

串口配置 ​

PX4 defines default functions for many flight controller ports, which is why you can plug a GPS module into the port labelled GPS 1, an RC receiver into RC IN, or a telemetry module into TELEM 1, and generally they will just work.

The functions assigned to ports are fully configurable using appropriate parameters (in most cases). You can assign any unused port to any function, or reassign a port to use it for something else.

通过配置，可以轻松地(例如)：

  • Run MAVLink on a different port, change the streamed messages, or switch a TELEM port to use ROS 2/XRCE-DDS.
  • Change the baud rate on a port or set the UDP port
  • Setup dual GPS.
  • Enable sensors that run on a serial port, such as some distance sensors.

INFO

  • Some ports cannot be configured because they are used for a very specific purpose such as the system console.
  • The mapping of specific devices to port names on the flight controller is explained in Serial Port Mapping.

Configuration Parameters ​

The serial port configuration parameters allow you to assign a particular function or support for particular hardware to a particular port. These parameters follow the naming pattern *_CONFIG or *_CFG

QGroundControl only displays the parameters for services/drivers that are present in firmware.

At time of writing the current set is:

Some functions/features may define additional configuration parameters, which will follow a similar naming pattern to the port configuration prefix. For example, MAV_0_CONFIG enables MAVLink on a particular port, but you may also need to set MAV_0_FLOW_CTRL, MAV_0_FORWARD, MAV_0_MODE and so on.

如何配置端口 ​

All the serial drivers/ports are configured in the same way:

  1. Set the configuration parameter for the service/peripheral to the port it will use.
  2. Reboot the vehicle in order to make the additional configuration parameters visible.
  3. Set the baud rate parameter for the selected port to the desired value (e.g. SER_GPS1_BAUD)
  4. Configure module-specific parameters (i.e. MAVLink streams and data rate configuration).

The GPS/Compass > Secondary GPS section provides a practical example of how to configure a port in QGroundControl (it shows how to use GPS_2_CONFIG to run a secondary GPS on the TELEM 2 port).

Similarly PX4 Ethernet Setup > PX4 MAVLink Serial Port Configuration explains the setup for Ethernet serial ports, and MAVLink Peripherals (OSD/GCS/Companion Computers/etc.) explains the configuration for MAVLink serial ports.

Deconflicting Ports ​

Port conflicts are handled by system startup, which ensures that at most one service is run on a specific port. For example, it is not possible to start a MAVLink instance on a specific serial device, and then launch a driver that uses the same serial device.

WARNING

At time of writing there is no user feedback about conflicting ports.

Default Serial Port Configuration ​

TIP

These port mappings can be disabled by setting the associated configuration parameter to Disabled.

The following ports are commonly mapped to specific functions on all boards:

Other ports generally have no assigned functions by default (are disabled).

故障处理 ​

Configuration Parameter Missing from QGroundControl ​

QGroundControl only displays the parameters for services/drivers that are present in firmware. If a parameter is missing, then you may need to add it in firmware.

PX4 firmware includes most drivers by default on Pixhawk-series boards. Flash-limited boards may comment out/omit the driver (at time of writing this only affects boards based on FMUv2).

You can include the missing driver in firmware by enabling the driver in the default.px4board config file that corresponds to the board you want to build for. For example, to enable the SRF02 driver, you would a the following line to the px4board.

CONFIG_DRIVERS_DISTANCE_SENSOR_SRF02=y

An easier method would be using boardconfig which launches a GUI where you can easily search, disable and enable modules. To launch boardconfig type:

make <vendor>_<board>_<label> boardconfig

You will then need to build the firmware for your platform, as described in Building PX4 Software.

更多信息 ​