Omnibus F4 SD

WARNING

This flight controller has been discontinued and is no longer commercially available.

WARNING

PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for support or compliance issues.

The Omnibus F4 SD is a controller board designed for racers. In contrast to a typical racer board it has some additional features, such as an SD card and a faster CPU.

These are the main differences compared to a Pixracer:

• Lower price
• Fewer IO ports (though it's still possible to attach a GPS or a Flow sensor for example)
• Requires external pull up resistor on the I2C bus for external GPS, see I2C below.
• Less RAM (192 KB vs. 256 KB) and FLASH (1 MB vs. 2 MB)
• Same board dimensions as a Pixracer, but slightly smaller form factor (because it has less connectors)
• Integrated OSD (not yet implemented in software)

TIP

All the usual PX4 features can still be used for your racer!

This flight controller is manufacturer supported.

主要特性

• Main System-on-Chip: STM32F405RGT6
  • CPU: 168 MHz ARM Cortex M4 with single-precision FPU
  • RAM: 192 KB SRAM
  • FLASH: 1 MB
• Standard racer form factor: 36x36 mm with standard 30.5 mm hole pattern
• MPU6000 Accel / Gyro
• BMP280 Baro (not all boards have it mounted)
• microSD (for logging)
• Futaba S.BUS and S.BUS2 / Spektrum DSM2 and DSMX / Graupner SUMD / PPM input / Yuneec ST24
• OneShot PWM out (configurable)
• Built-in current sensor
• Built-in OSD chip (AB7456 via SPI)

在哪里买

The board is produced by different vendors, with some variations (e.g. with or without a barometer).

PX4 is compatible with boards that support the Betaflight OMNIBUSF4SD target (if OMNIBUSF4SD is present on the product page the board should work with PX4).

TIP

Any Omnibus F4 labeled derivative (e.g. clone) should work as well. However, power distribution on these boards is of varying quality.

These are the boards tested and known to work:

• Hobbywing XRotor Flight Controller F4

  This board fits on top of the Hobbywing XRotor Micro 40A 4in1 ESC without soldering. This ESC board also provides power for the Omnibus board.

:::

Purchase from:

• Hobbywing XRotor F4 Flight Controller w/OSD (getfpv)

• Original Airbot Omnibus F4 SD

  Purchase from:

  • Airbot (CN manufacturer)
  • Ready To Fly Quads (US reseller)

Accessories include:

• ESP8266 WiFi Module for MAVLink telemetry. You need to connect these pins: GND, RX, TX, VCC and CH-PD (CH-PD to 3.3V). The baud rate is 921600.

连接器

Boards from different vendors (based on this design) can have significantly different layout. Layouts/Silkscreens for various versions are shown below.

Airbot Omnibus F4 SD

Below are silkscreens for the Airbot Omnibus F4 SD (V1), showing both top and bottom.

Hobbywing XRotor Flight Controller F4

Below are silkscreens for the Hobbywing XRotor Flight Controller F4.

针脚定义

遥控器

RC is connected to one of the following ports:

• UART1
• SBUS/PPM port (via inverter, internally goes to UART1)

INFO

Some Omnibus F4 boards have a jumper connecting either or both the MCU SBUS and PPM to a single pin header. Set your jumper or solder bridge to the appropriate MCU pin before use.

UARTs

• UART6: GPS port

  • TX: MCU pin PC6

  • RX: MCU pin PC7

  • Airbot Omnibus F4 SD Pinout is on Port J10 (TX6/RX6):

  

• UART4

  • TX: MCU pin PA0
  • RX: MCU pin PA1
  • 57600 波特率
  • This can be configured as the TELEM 2 port.
  • Airbot Omnibus F4 SD Pinout:
    • TX: RSSI pin
    • RX: PWM out 5

  

  

I2C

There is one I2C port available via:

• SCL: MCU pin PB10 (might be labeled as TX3)
• SDA: MCU pin PB11 (might be labeled as RX3)

INFO

You will need external pullups on both signals (clock and data). You can use 2.2k pullups for example to attach an external mag.

• Airbot Omnibus F4 SD Pinout is on Port J10 (SCL [clock] / SCA [data]):

Here is an example implementation. I used a Spektrum plug to get 3.3v from the DSM port, connecting only 3.3v + to each line via 2.2k resistor.

Serial Port Mapping

UART	设备	Port
USART1	/dev/ttyS0	SerialRX
USART4	/dev/ttyS1	TELEM1
USART6	/dev/ttyS2	GPS

RC Telemetry

The Omnibus supports telemetry to the RC Transmitter using FrSky Telemetry or CRSF Crossfire Telemetry.

CRSF Crossfire Telemetry

TBS CRSF Telemetry may be used to send telemetry data from the flight controller (the vehicle's attitude, battery, flight mode and GPS data) to an RC transmitter such as a Taranis.

Benefits over FrSky telemetry include:

• Only a single UART is needed for RC and telemetry.
• The CRSF protocol is optimized for low latency.
• 150 Hz RC update rate.
• The signals are uninverted and thus no (external) inverter logic is required.

INFO

If you use CRSF Telemetry you will need to build custom PX4 firmware. By contrast, FrSky telemetry can use prebuilt firmware.

For Omnibus we recommend the TBS Crossfire Nano RX, since it is specifically designed for small Quads.

On the handheld controller (e.g. Taranis) you will also need a Transmitter Module. This can be plugged into the back of the RC controller.

INFO

The referenced links above contains the documentation for the TX/RX modules.

设置

Connect the Nano RX and Omnibus pins as shown:

Omnibus UART1	Nano RX
TX	Ch2
RX	Ch1

Next update the TX/RX modules to use the CRSF protocol and set up telemetry. Instructions for this are provided in the TBS Crossfire Manual (search for 'Setting up radio for CRSF').

PX4 CRSF Configuration

You will need to build custom firmware to use CRSF. For more information see CRSF Telemetry.

原理图

The schematics are provided by Airbot: OmnibusF4-Pro-Sch.pdf.

PX4 Bootloader Update

The board comes pre-installed with Betaflight. Before PX4 firmware can be installed, the PX4 bootloader must be flashed. Download the omnibusf4sd_bl.hex bootloader binary and read this page for flashing instructions.

编译固件

To build PX4 for this target:

make omnibus_f4sd_default

Installing PX4 Firmware

You can use either pre-built firmware or your own custom firmware.

WARNING

If you use CRSF Telemetry in your radio system, as describe above, then you must use custom firmware.

The firmware can be installed in any of the normal ways:

• Build and upload the source

  make omnibus_f4sd_default upload

• Load the firmware using QGroundControl.

配置

In addition to the basic configuration, the following parameters are important:

参数	设置
SYS_HAS_MAG	This should be disabled since the board does not have an internal mag. You can enable it if you attach an external mag.
SYS_HAS_BARO	Disable this if your board does not have a barometer.

Further Info

This page provides a good overview with pinouts and setup instructions.