EstimatorStatus (UORB message)
c
uint64 timestamp # time since system start (microseconds)
uint64 timestamp_sample # the timestamp of the raw data (microseconds)
float32[3] output_tracking_error # return a vector containing the output predictor angular, velocity and position tracking error magnitudes (rad), (m/s), (m)
uint16 gps_check_fail_flags # Bitmask to indicate status of GPS checks - see definition below
# bits are true when corresponding test has failed
uint8 GPS_CHECK_FAIL_GPS_FIX = 0 # 0 : insufficient fix type (no 3D solution)
uint8 GPS_CHECK_FAIL_MIN_SAT_COUNT = 1 # 1 : minimum required sat count fail
uint8 GPS_CHECK_FAIL_MAX_PDOP = 2 # 2 : maximum allowed PDOP fail
uint8 GPS_CHECK_FAIL_MAX_HORZ_ERR = 3 # 3 : maximum allowed horizontal position error fail
uint8 GPS_CHECK_FAIL_MAX_VERT_ERR = 4 # 4 : maximum allowed vertical position error fail
uint8 GPS_CHECK_FAIL_MAX_SPD_ERR = 5 # 5 : maximum allowed speed error fail
uint8 GPS_CHECK_FAIL_MAX_HORZ_DRIFT = 6 # 6 : maximum allowed horizontal position drift fail - requires stationary vehicle
uint8 GPS_CHECK_FAIL_MAX_VERT_DRIFT = 7 # 7 : maximum allowed vertical position drift fail - requires stationary vehicle
uint8 GPS_CHECK_FAIL_MAX_HORZ_SPD_ERR = 8 # 8 : maximum allowed horizontal speed fail - requires stationary vehicle
uint8 GPS_CHECK_FAIL_MAX_VERT_SPD_ERR = 9 # 9 : maximum allowed vertical velocity discrepancy fail
uint8 GPS_CHECK_FAIL_SPOOFED = 10 # 10 : GPS signal is spoofed
uint64 control_mode_flags # Bitmask to indicate EKF logic state
uint8 CS_TILT_ALIGN = 0 # 0 - true if the filter tilt alignment is complete
uint8 CS_YAW_ALIGN = 1 # 1 - true if the filter yaw alignment is complete
uint8 CS_GPS = 2 # 2 - true if GPS measurements are being fused
uint8 CS_OPT_FLOW = 3 # 3 - true if optical flow measurements are being fused
uint8 CS_MAG_HDG = 4 # 4 - true if a simple magnetic yaw heading is being fused
uint8 CS_MAG_3D = 5 # 5 - true if 3-axis magnetometer measurement are being fused
uint8 CS_MAG_DEC = 6 # 6 - true if synthetic magnetic declination measurements are being fused
uint8 CS_IN_AIR = 7 # 7 - true when thought to be airborne
uint8 CS_WIND = 8 # 8 - true when wind velocity is being estimated
uint8 CS_BARO_HGT = 9 # 9 - true when baro height is being fused as a primary height reference
uint8 CS_RNG_HGT = 10 # 10 - true when range finder height is being fused as a primary height reference
uint8 CS_GPS_HGT = 11 # 11 - true when GPS height is being fused as a primary height reference
uint8 CS_EV_POS = 12 # 12 - true when local position data from external vision is being fused
uint8 CS_EV_YAW = 13 # 13 - true when yaw data from external vision measurements is being fused
uint8 CS_EV_HGT = 14 # 14 - true when height data from external vision measurements is being fused
uint8 CS_BETA = 15 # 15 - true when synthetic sideslip measurements are being fused
uint8 CS_MAG_FIELD = 16 # 16 - true when only the magnetic field states are updated by the magnetometer
uint8 CS_FIXED_WING = 17 # 17 - true when thought to be operating as a fixed wing vehicle with constrained sideslip
uint8 CS_MAG_FAULT = 18 # 18 - true when the magnetometer has been declared faulty and is no longer being used
uint8 CS_ASPD = 19 # 19 - true when airspeed measurements are being fused
uint8 CS_GND_EFFECT = 20 # 20 - true when when protection from ground effect induced static pressure rise is active
uint8 CS_RNG_STUCK = 21 # 21 - true when a stuck range finder sensor has been detected
uint8 CS_GPS_YAW = 22 # 22 - true when yaw (not ground course) data from a GPS receiver is being fused
uint8 CS_MAG_ALIGNED = 23 # 23 - true when the in-flight mag field alignment has been completed
uint8 CS_EV_VEL = 24 # 24 - true when local frame velocity data fusion from external vision measurements is intended
uint8 CS_SYNTHETIC_MAG_Z = 25 # 25 - true when we are using a synthesized measurement for the magnetometer Z component
uint8 CS_VEHICLE_AT_REST = 26 # 26 - true when the vehicle is at rest
uint8 CS_GPS_YAW_FAULT = 27 # 27 - true when the GNSS heading has been declared faulty and is no longer being used
uint8 CS_RNG_FAULT = 28 # 28 - true when the range finder has been declared faulty and is no longer being used
uint32 filter_fault_flags # Bitmask to indicate EKF internal faults
# 0 - true if the fusion of the magnetometer X-axis has encountered a numerical error
# 1 - true if the fusion of the magnetometer Y-axis has encountered a numerical error
# 2 - true if the fusion of the magnetometer Z-axis has encountered a numerical error
# 3 - true if the fusion of the magnetic heading has encountered a numerical error
# 4 - true if the fusion of the magnetic declination has encountered a numerical error
# 5 - true if fusion of the airspeed has encountered a numerical error
# 6 - true if fusion of the synthetic sideslip constraint has encountered a numerical error
# 7 - true if fusion of the optical flow X axis has encountered a numerical error
# 8 - true if fusion of the optical flow Y axis has encountered a numerical error
# 9 - true if fusion of the North velocity has encountered a numerical error
# 10 - true if fusion of the East velocity has encountered a numerical error
# 11 - true if fusion of the Down velocity has encountered a numerical error
# 12 - true if fusion of the North position has encountered a numerical error
# 13 - true if fusion of the East position has encountered a numerical error
# 14 - true if fusion of the Down position has encountered a numerical error
# 15 - true if bad delta velocity bias estimates have been detected
# 16 - true if bad vertical accelerometer data has been detected
# 17 - true if delta velocity data contains clipping (asymmetric railing)
float32 pos_horiz_accuracy # 1-Sigma estimated horizontal position accuracy relative to the estimators origin (m)
float32 pos_vert_accuracy # 1-Sigma estimated vertical position accuracy relative to the estimators origin (m)
float32 hdg_test_ratio # low-pass filtered ratio of the largest heading innovation component to the innovation test limit
float32 vel_test_ratio # low-pass filtered ratio of the largest velocity innovation component to the innovation test limit
float32 pos_test_ratio # low-pass filtered ratio of the largest horizontal position innovation component to the innovation test limit
float32 hgt_test_ratio # low-pass filtered ratio of the vertical position innovation to the innovation test limit
float32 tas_test_ratio # low-pass filtered ratio of the true airspeed innovation to the innovation test limit
float32 hagl_test_ratio # low-pass filtered ratio of the height above ground innovation to the innovation test limit
float32 beta_test_ratio # low-pass filtered ratio of the synthetic sideslip innovation to the innovation test limit
uint16 solution_status_flags # Bitmask indicating which filter kinematic state outputs are valid for flight control use.
# 0 - True if the attitude estimate is good
# 1 - True if the horizontal velocity estimate is good
# 2 - True if the vertical velocity estimate is good
# 3 - True if the horizontal position (relative) estimate is good
# 4 - True if the horizontal position (absolute) estimate is good
# 5 - True if the vertical position (absolute) estimate is good
# 6 - True if the vertical position (above ground) estimate is good
# 7 - True if the EKF is in a constant position mode and is not using external measurements (eg GPS or optical flow)
# 8 - True if the EKF has sufficient data to enter a mode that will provide a (relative) position estimate
# 9 - True if the EKF has sufficient data to enter a mode that will provide a (absolute) position estimate
# 10 - True if the EKF has detected a GPS glitch
# 11 - True if the EKF has detected bad accelerometer data
uint8 reset_count_vel_ne # number of horizontal position reset events (allow to wrap if count exceeds 255)
uint8 reset_count_vel_d # number of vertical velocity reset events (allow to wrap if count exceeds 255)
uint8 reset_count_pos_ne # number of horizontal position reset events (allow to wrap if count exceeds 255)
uint8 reset_count_pod_d # number of vertical position reset events (allow to wrap if count exceeds 255)
uint8 reset_count_quat # number of quaternion reset events (allow to wrap if count exceeds 255)
float32 time_slip # cumulative amount of time in seconds that the EKF inertial calculation has slipped relative to system time
bool pre_flt_fail_innov_heading
bool pre_flt_fail_innov_height
bool pre_flt_fail_innov_pos_horiz
bool pre_flt_fail_innov_vel_horiz
bool pre_flt_fail_innov_vel_vert
bool pre_flt_fail_mag_field_disturbed
uint32 accel_device_id
uint32 gyro_device_id
uint32 baro_device_id
uint32 mag_device_id
# legacy local position estimator (LPE) flags
uint8 health_flags # Bitmask to indicate sensor health states (vel, pos, hgt)
uint8 timeout_flags # Bitmask to indicate timeout flags (vel, pos, hgt)
float32 mag_inclination_deg
float32 mag_inclination_ref_deg
float32 mag_strength_gs
float32 mag_strength_ref_gs