Modules Reference: Magnetometer (Driver)
ak09916
Source: drivers/magnetometer/akm/ak09916
Usage
ak09916 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 12
[-R <val>] Rotation
default: 0
stop
status print status info
ak8963
Source: drivers/magnetometer/akm/ak8963
Usage
ak8963 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 12
[-R <val>] Rotation
default: 0
stop
status print status info
bmm150
Source: drivers/magnetometer/bosch/bmm150
Usage
bmm150 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 16
[-R <val>] Rotation
default: 0
stop
status print status info
bmm350
Source: drivers/magnetometer/bosch/bmm350
Usage
bmm350 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 20
[-R <val>] Rotation
default: 0
stop
status print status info
hmc5883
Source: drivers/magnetometer/hmc5883
Usage
hmc5883 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
[-T] Enable temperature compensation
stop
status print status info
iis2mdc
Source: drivers/magnetometer/st/iis2mdc
Usage
iis2mdc <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 48
stop
status print status info
ist8308
Source: drivers/magnetometer/isentek/ist8308
Usage
ist8308 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 12
[-R <val>] Rotation
default: 0
stop
status print status info
ist8310
Source: drivers/magnetometer/isentek/ist8310
Usage
ist8310 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 14
[-R <val>] Rotation
default: 0
stop
status print status info
lis2mdl
Source: drivers/magnetometer/lis2mdl
Usage
lis2mdl <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 30
[-R <val>] Rotation
default: 0
stop
status print status info
lis3mdl
Source: drivers/magnetometer/lis3mdl
Usage
lis3mdl <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 30
[-R <val>] Rotation
default: 0
reset
stop
status print status info
lsm9ds1_mag
Source: drivers/magnetometer/lsm9ds1_mag
Usage
lsm9ds1_mag <command> [arguments...]
Commands:
start
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
stop
status print status info
mmc5983ma
Source: drivers/magnetometer/memsic/mmc5983ma
Usage
mmc5983ma <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 48
reset
stop
status print status info
qmc5883l
Source: drivers/magnetometer/qmc5883l
Usage
qmc5883l <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 13
[-R <val>] Rotation
default: 0
stop
status print status info
rm3100
Source: drivers/magnetometer/rm3100
Usage
rm3100 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-s] Internal SPI bus(es)
[-S] External SPI bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
stop
status print status info
vcm1193l
Source: drivers/magnetometer/vtrantech/vcm1193l
Usage
vcm1193l <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-R <val>] Rotation
default: 0
stop
status print status info