Modules Reference: Airspeed Sensor (Driver)
asp5033
Source: drivers/differential_pressure/asp5033
Description
Driver to enable an external [ASP5033] (https://www.qio-tek.com/index.php/product/qiotek-asp5033-dronecan-airspeed-and-compass-module/) TE connected via I2C. This is not included by default in firmware. It can be included with terminal command: "make <your_board> boardconfig" or in default.px4board with adding the line: "CONFIG_DRIVERS_DIFFERENTIAL_PRESSURE_ASP5033=y" It can be enabled with the "SENS_EN_ASP5033" parameter set to 1.
Usage
asp5033 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 109
stop
status print status infoauav
Source: drivers/differential_pressure/auav
Usage
auav <command> [arguments...]
Commands:
start
[-D] Differential pressure sensing
[-A] Absolute pressure sensing
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 38
stop
status print status infoets_airspeed
Source: drivers/differential_pressure/ets
Usage
ets_airspeed <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 117
stop
status print status infoms4515
Source: drivers/differential_pressure/ms4515
Usage
ms4515 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 70
stop
status print status infoms4525do
Source: drivers/differential_pressure/ms4525do
Usage
ms4525do <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 40
stop
status print status infoms5525dso
Source: drivers/differential_pressure/ms5525dso
Usage
ms5525dso <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 118
stop
status print status infosdp3x
Source: drivers/differential_pressure/sdp3x
Usage
sdp3x <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es)
[-X] External I2C bus(es)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 33
[-k] if initialization (probing) fails, keep retrying periodically
stop
status print status info