Skip to content

Holybro QAV250 + Pixhawk 4 Mini Build (Discontinued)

INFO

The Holybro Pixhawk 4 Mini QAV250 Kit is no longer available.

The instructions have been left here because very similar kits based on the Pix32 v6 are available here. These instructions can therefore still be followed (and might be updated to Pix32 v6).

The complete kits include a carbon-fibre QAV250 racing frame, flight controller and almost all other components needed (except battery and receiver). There are variants of the kit both with and without FPV support. This topic provides full instructions for building the kit and configuring PX4 using QGroundControl.

Key information

  • Frame: Holybro QAV250
  • Flight controller: Pixhawk 4 Mini
  • Assembly time (approx.): 3.5 hours (2 for frame, 1.5 autopilot installation/configuration)

Assembled Holybro QAV250 with Pixhawk4 Mini

Quickstart Guide

Pixhawk 4 Mini QAV250 Kit Quickstart Guide

Bill of materials

The Holybro QAV250 Kit kits includes almost all required components:

  • Holybro Transceiver Telemetry Radio V3
  • Power module holybro
  • Fully assembled Power Management Board with ESCs
  • Motors - DR2205 KV2300
  • 5” Plastic Props
  • Carbon fiber 250 airframe with hardware
  • Foxer camera
  • Vtx 5.8ghz

Additionally you will need a battery and receiver (+compatible transmitter). This build uses:

硬件

This section lists all hardware for the frame and the autopilot installation.

Frame QAV250

描述Quantity
Unibody frame plate1
Flight controller cover plate1
PDB1
Camera plate1
35mm standoffs6
Vinyl screws and nuts4
15mm steel screws8
Steel nuts8
7mm steel screws12
Velcro battery strap1
Foam for battery1
Landing pads4

QAV250 components for frame

Electronics

描述Quantity
Motors - DR2205 KV23004
Fully assembled Power Management Board with ESCs4
Holybro power module1
Fr-sky D4R-II receiver1
Pixhawk 4 mini1
Holybro GPS Neo-M8N1
Holybro Transceiver Telemetry Radio V31
Battery lumenier 1300 mAh 4S 14.8V1
Vtx 5.8gHz1
FPV camera (Complete Kit - only)1

The image below shows both frame and electronic components.

QAV250 Frame/Pixhawk 4 Mini Electronics before assembly

组装

Estimated time to assemble frame is 2 hours and 1.5 hours installing the autopilot and configuring the airframe in QGroundControl.

Tools needed

The following tools are used in this assembly:

  • 2.0mm Hex screwdriver
  • 3mm Phillips screwdriver
  • Wire cutters
  • Precision tweezers

Tools required for assembling QAV250

Frame assembly

  1. Attach arms to the button plate with the 15mm screws as shown:

    QAV250 Add arms to button plate

  2. Put the short plate over the arms

    QAV250 Add short plate over arms

  3. Put the nuts on the 15mm screws (shown next step)

  4. Insert the plastic screws into the indicated holes (note that this part of the frame faces down when the vehicle is complete). QAV250 Add nuts to 15mm screws and put  plastic nuts in holes

  5. Add the plastic nuts to the screws (turn over, as shown) QAV250 Plastic nuts onto screws

  6. Lower the power module over the plastic screws and then add the plastics standoffs QAV250 Add power module and standoffs

  7. Put the flight controller plate on the standoffs (over the power module) QAV250 Add flight controller plate

  8. Attach the motors. The motors have an arrow indicating the direction of rotation. QAV250 Add motors

  9. Use double sided tape from kit to attach the Pixhawk 4 Mini to the flight controller plate. QAV250 Add doublesided tape

  10. Connect the power module's "power" cable to Pixhawk 4 mini. QAV250 Power Pixhawk

  11. Attach the aluminium standoffs to the button plate QAV250 Aluminium standoffs

  12. Connect the Esc’s with the motors and hold. In this image shown the order of the motors and direction of the rotation. QAV250 Connect ESCs

    Connect the motors on the ESC’s, make sure the motors turns to the correct side, if the motor turns of the opposite side change the cable A to the pad C and C to the pad A of the ESC.

    WARNING

    Test motor directions with propellers removed.

:::

![QAV250 Connect ESCs to Power](../../assets/airframes/multicopter/qav250_holybro_pixhawk4_mini/11b_escs.jpg)
  1. Connect the signal ESC cables to the PWM outputs of the Pixhawk in the correct order (see previous image)

    QAV250 Connect ESCs to Pixhawk PWM

  2. Connect the receiver.

    • If using a PPM receiver connect to the PPM port.

      QAV250 Connect Receiver PPM

    • If using the SBUS receiver connect to the RC IN port

      QAV250 Connect Receiver SBUS

  3. Connect the telemetry module. Paste the module with double tape and connect on the port of the telemetry.

    QAV250 Telemetry module

  4. Connect the GPS module

    QAV250 Connect GPS

    Attach the module on the top plate (using provided 3M tape, or paste). Then put the top plate on the standoffs as shown

    QAV250 Connect GPS

  5. The last "mandatory" assembly step is to add the velcro to hold the battery

    QAV250 Velcro battery strap

The "basic" frame build is now complete (though if you need them, you can find more information about connecting components in the Pixhawk 4 Wiring Quickstart).

If you have the "basic" version of the kit, you can now jump ahead to instructions on how to Install/Configure PX4.

FPV Assembly

The "Complete" version of the kit additionally comes with an FPV system, which is mounted on the front of the vehicle as shown.

QAV250 FPV Attach

The steps to install the kit are:

  1. Install the camera bracket on the frame Camera Connection
  2. Install the camera on the bracket Camera on Bracket
  3. The power module on the complete kit comes with wiring ready to connect the Video Transmitter and Camera: Connecting FPV
    • Attach the camera connector Camera Connection The wires are: blue=voltage sensor, yellow=video out, black=ground, red=+voltage.
    • Connect the Video Transmitter (VTX) connector Video Transmitter Connection The wires are: yellow=video out, black=ground, red=+voltage.
  4. Secure the Video Transmitter and OSD board to the frame using tape.

INFO

If you have to wire the system yourself, the diagram below shows all the connections between camera, VTX and power module: QAV250 FPV Wiring

PX4 配置

QGroundControl is used to install the PX4 autopilot and configure/tune it for the QAV250 frame. Download and install QGroundControl for your platform.

TIP

Full instructions for installing and configuring PX4 can be found in Basic Configuration.

First update the firmware, airframe, and actuator mappings:

  • Firmware

  • Airframe

    INFO

    You will need to select the HolyBro QAV250 airframe (Quadrotor x > HolyBro QAV250).

    QGC - Select HolyBro QAV250 airframe

:::

  • Actuators
    • You should not need to update the vehicle geometry (as this is a preconfigured airframe).
    • Assign actuator functions to outputs to match your wiring.
      • For the Pixhawk 4 Mini, and other controllers that do not have an I/O board, you will need to assign actuators to outputs on the PWM AUX tab in the configuration screen.
      • The Pix32 v6 has an I/O board, so you can assign to either AUX or MAIN.
    • Test the configuration using the sliders.

Then perform the mandatory setup/calibration:

Ideally you should also do:

调试

Airframe selection sets default autopilot parameters for the frame. These may be good enough to fly with, but you should tune each frame build.

For instructions on how, start from Autotune.

Acknowledgements

This build log was provided by the PX4 Test Team.