Holybro Durandal
WARNING
PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues.
Durandal® is the latest update to the successful family of Holybro flight controllers. It was designed and developed by Holybro.
At high level, some of the key features are:
- Integrated temperature control for sensors.
- Powerful STM32H7 microcontroller running at 480MHz. 2 MB of Flash memory and 1 MB of RAM.
- New sensors with higher temperature stability.
- Internal vibration isolation system.
- Dual high-performance, low-noise IMUs on board are designed for demanding stabilization applications.
A summary of the key features, assembly, and purchase links can be found below.
INFO
This flight controller is manufacturer supported.
总览
Technical Specifications
- Main FMU Processor: STM32H743
- 32 Bit Arm ® Cortex® -M7, 480MHz, 2MB memory, 1MB RAM
- IO 处理器：STM32F100
- 32 Bit Arm ® Cortex® -M3, 24MHz, 8KB SRAM
- On-board sensors
- 加速度计 / 陀螺仪：ICM-20689
- Accel/Gyro: BMI088 or ICM20602
- Mag: IST8310
- 气压计：MS5611
- GPS：ublox Neo-M8N GPS/GLONASS 接收器；集成磁力计 IST8310
接口
- 8-13 PWM servo outputs (8 from IO, 5 from FMU)
- FMU上有6个专用PWM/Capture输入
- Dedicated R/C input for Spektrum / DSM
- Dedicated R/C input for CPPM and S.Bus
- Dedicated S.Bus servo output and analog / PWM RSSI input
- 5个通用串行口
- 3 with full flow control
- 1 with separate 1.5A current limit
- 3 个 I2C 接口
- 4路SPI总线
- 1 internal high speed SPI sensor bus with 4 chip selects and 6 DRDYs
- 1 internal low noise SPI bus dedicated for XXX
- Barometer with 2 chip selects, no DRDYs
- 1 internal SPI bus dedicated for FRAM
- Supports temperature control located on sensor module
- 1 external SPI buses
- Up to 2 CANBuses for dual CAN
- Each CANBus has individual silent controls or ESC RX-MUX control
- 2个电池电流/电压模拟输入口
- 2 additional analog inputs
Electrical Data
- 电源模块输出：4.9~5.5V
- Max input voltage: 6V
- 最大电流感应：120A
- USB 电源输入：4.75~5.25V
- 伺服导轨输入电压：0~36V
Mechanical Data
- Dimensions: 80x45x20.5mm
- 重量：68.8g
其它特性
- Operating temperature: ~40~85C
- Storage temperature: -40~85C
- CE
- FCC
- RoHS compliant (lead-free)
For more information see: Durandal Technical Data Sheet.
购买渠道
Order from Holybro.
Connections
The locations of ports/connections are shown here (and below in the pinouts section).
Top
Front
Back
Right
Left
尺寸
All dimensions are in millimeters.
组装 / 设置
The Durandal Wiring Quick Start provides instructions on how to assemble required/important peripherals including GPS, Power Management Board etc.
编译固件
TIP
Most users will not need to build this firmware! It is pre-built and automatically installed by QGroundControl when appropriate hardware is connected.
To build PX4 for this target:
make holybro_durandal-v1_default串口映射
| UART | 设备 | Port |
|---|---|---|
| USART1 | /dev/ttyS0 | GPS1 |
| USART2 | /dev/ttyS1 | TELEM1 |
| USART3 | /dev/ttyS2 | TELEM2 |
| UART4 | /dev/ttyS3 | TELEM4/GPS2 |
| USART6 | /dev/ttyS4 | TELEM3 |
| UART7 | /dev/ttyS5 | Debug Console |
| UART8 | /dev/ttyS6 | PX4IO |
调试接口
The PX4 System Console and SWD interface run on the Debug Port.
The pinouts and connector comply with the Pixhawk Debug Mini interface defined in the Pixhawk Connector Standard.
For wiring and debugging information see the above links.
INFO
No Debug port is exposed for the I/O board.
外部设备
支持的平台/机身
Any multicopter / airplane / rover or boat that can be controlled with normal RC servos or Futaba S-Bus servos.
The complete set of supported configurations can be seen in the Airframes Reference.
针脚定义
Durandal pinouts are listed below. These can also be downloaded from here.
Top Pinouts
Front Pinouts
SUBS Out port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | - | - |
| 2 (yellow) | SBUS_OUT/RSSI_IN | +3.3V |
| 3 (black) | GND | GND |
DSM RC port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VDD_3V3 | +3.3V |
| 2 (yellow) | DSM_IN | +3.3V |
| 3 (black) | GND | GND |
I2C A port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | SCL4 | +3.3V |
| 3 (black) | SDA4 | +3.3V |
| 4 (black) | GND | GND |
CAN1 port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | CAN H | +3.3V |
| 3 (black) | CAN L | +3.3V |
| 4 (black) | GND | GND |
GPS 接口
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | TX (out) | +3.3V |
| 3 (black) | RX (in) | +3.3V |
| 4 (black) | SCL1 | +3.3V |
| 5 (black) | SDA1 | +3.3V |
| 6 (black) | SAFETY_SWITCH | +3.3V |
| 7 (black) | SAFETY_SWITCH_LED | +3.3V |
| 8 (black) | VDD_3V3 | +3.3V |
| 9 (black) | BUZZER | +5V |
| 10 (black) | GND | GND |
TELEM4 I2CB ports
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | TX (out) | +3.3V |
| 3 (black) | RX (in) | - |
| 4 (black) | SCL2 | - |
| 5 (black) | SDA2 | +3.3V |
| 6 (black) | GND | GND |
TELEM3, TELEM2, TELEM1 port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | TX (out) | +3.3V |
| 3 (black) | RX (in) | +3.3V |
| 4 (black) | CTS（输入） | +3.3V |
| 5 (black) | RTS（输出） | +3.3V |
| 6 (black) | GND | GND |
POWER port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | VCC | +5V |
| 3 (black) | 电流 | +3.3V |
| 4 (black) | 电压 | +3.3V |
| 5 (black) | GND | GND |
| 6 (black) | GND | GND |
Back Pinouts
MAIN Out
| 针脚 | 信号 | 电压 | + | - |
|---|---|---|---|---|
| 1 | IO_CH1 | +3.3V | VDD_SERVO | GND |
| 2 | IO_CH2 | +3.3V | VDD_SERVO | GND |
| 3 | IO_CH3 | +3.3V | VDD_SERVO | GND |
| 4 | IO_CH4 | +3.3V | VDD_SERVO | GND |
| 5 | IO_CH5 | +3.3V | VDD_SERVO | GND |
| 6 | IO_CH6 | +3.3V | VDD_SERVO | GND |
| 7 | IO_CH7 | +3.3V | VDD_SERVO | GND |
| 8 | IO_CH8 | +3.3V | VDD_SERVO | GND |
AUX Out
| 针脚 | 信号 | 电压 | + | - |
|---|---|---|---|---|
| 1 | FMU_CH1 | +3.3V | VDD_SERVO | GND |
| 2 | FMU_CH2 | +3.3V | VDD_SERVO | GND |
| 3 | FMU_CH3 | +3.3V | VDD_SERVO | GND |
| 4 | FMU_CH4 | +3.3V | VDD_SERVO | GND |
| 5 | FMU_CH5 | +3.3V | VDD_SERVO | GND |
RC IN
| 针脚 | 信号 | 电压 |
|---|---|---|
| S | SBUS_IN/PPM_IN | +3.3V |
| + | VCC | +5V |
| - | GND | GND |
Right-side Pinouts
CAN2 port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | CAN H | +3.3V |
| 3 (black) | CAN L | +3.3V |
| 4 (black) | GND | GND |
CAP & ADC IN port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | FMU_CAP6 | +3.3V |
| 3 (black) | FMU_CAP5 | +3.3V |
| 4 (black) | FMU_CAP4 | +3.3V |
| 5 (black) | FMU_CAP3 | +3.3V |
| 6 (black) | FMU_CAP2 | +3.3V |
| 7 (black) | FMU_CAP1 | +3.3V |
| 8 (black) | ADC1_SPARE_1 | +3.3V ++ |
| 9 (black) | ADC1_SPARE_2 | +6.6V ++ |
| 10 (black) | GND | GND |
WARNING
++ Sensors connected to pins 8, 9 must not send a signal exceeding the indicated voltage.
Left-side Pinouts
DEBUG port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VT | +3.3V |
| 2 (black) | TX | +3.3V |
| 3 (black) | RX | +3.3V |
| 4 (black) | SWDIO | +3.3V |
| 5 (black) | SWCLK | +3.3V |
| 6 (black) | GND | GND |
SPI port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VCC | +5V |
| 2 (black) | SCK | +3.3V |
| 3 (black) | MISO | +3.3V |
| 4 (black) | MOSI | +3.3V |
| 5 (black) | CS1 | +3.3V |
| 6 (black) | CS2 | +3.3V |
| 7 (black) | GND | GND |
USB port
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | VBUS | +5V |
| 2 (black) | DM | +3.3V |
| 3 (black) | DP | +3.3V |
| 4 (black) | GND | GND |