Holybro Pix32 v6
WARNING
PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues.
Pix32 v6® is the latest update to the pix32 v5 flight controllers. It is a variant of the Pixhawk 6C with a modular design and shares the same FMUv6C Target. It is comprised of a separate flight controller and carrier board which are connected by a 100 pin connector. It is designed for those pilots who need a high power, flexible and customizable flight control system.
It is equipped with a high performance H7 Processor, and comes with IMU redundancy, temperature-controlled IMU board, and cost effective design, delivering incredible performance and reliability. It complies with the Connector Standard.
简介
Inside the Pix32 v6, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.
The Pix32 v6’s H7 MCU contain the Arm® Cortex®-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models. It includes high-performance, low-noise IMUs on board, designed to be cost effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances.
This flight controller is perfect for people that is looking for a affordable and modular flight controller that can use a customized baseboard. We have made the pix32 v6 base board schematics public, you can either make a custom carrier board yourself or just let us help you with it. By using a customize baseboard, you can make sure that the physical size, pinouts and power distribution requirements match your vehicle perfectly, ensuring that you have all the connections you need and none of the expense and bulk of connectors you don’t.
Key Design Points
- High performance STM32H743 Processor with more computing power & RAM
- New cost-effective design with low-profile form factor
- Integrated vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
- IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs
Technical Specification
Processors & Sensors
- FMU Processor: STM32H743 
- 32 Bit Arm® Cortex®-M7, 480MHz, 2MB memory, 1MB SRAM 
- IO Processor: STM32F103
- 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM 
- On-board sensors 
- Accel/Gyro: ICM-42688-P 
- Accel/Gyro: BMI055 
- Mag: IST8310 
- 气压计：MS5611
Electrical data
- Voltage Ratings:
- Max input voltage: 6V
- USB Power Input: 4.75~5.25V
- Servo Rail Input: 0~36V
- Current Ratings:
- TELEM1 Max output current limiter: 1.5A
- All other port combined output current limiter: 1.5A
Mechanical data
- FC Module Dimensions: 44.8 x 44.8 x 13.5
- FC Module Weight: 36g
Interfaces
16- PWM servo outputs (8 from IO, 8 from FMU)
3个通用串行口
TELEM1- Full flow control, separate 1.5A current limitTELEM2- Full flow controlTELEM3
2 GPS ports
GPS1- Full GPS port (GPS plus safety switch)GPS2- Basic GPS port
1 I2C port
- Supports dedicated I2C calibration EEPROM located on sensor module
2 CAN Buses
- CAN Bus has individual silent controls or ESC RX-MUX control
2 Debug ports:
- FMU Debug
- I/O Debug
Dedicated R/C input for Spektrum / DSM and S.BUS, CPPM, analog / PWM RSSI
Dedicated S.BUS output
2 Power input ports (Analog)
其它特性:
- Operating & storage temperature: -40 ~ 85°c
购买渠道
Order from Holybro.
针脚定义
串口映射
| UART | 设备 | Port |
|---|---|---|
| USART1 | /dev/ttyS0 | GPS1 |
| USART2 | /dev/ttyS1 | TELEM3 |
| USART3 | /dev/ttyS2 | Debug Console |
| UART5 | /dev/ttyS3 | TELEM2 |
| USART6 | /dev/ttyS4 | PX4IO |
| UART7 | /dev/ttyS5 | TELEM1 |
| UART8 | /dev/ttyS6 | GPS2 |
尺寸
额定电压
Pix32 v6 can be triple-redundant on the power supply if three power sources are supplied. The three power rails are: USB, POWER1, POWER2 (N/A on Pix32 v6 Mini-Baseboard) .
Normal Operation Maximum Ratings
Under these conditions all power sources will be used in this order to power the system:
- POWER1 and POWER2 inputs (4.9V to 5.5V)
- USB input (4.75V to 5.25V)
Absolute Maximum Ratings
Under these conditions the system will not draw any power (will not be operational), but will remain intact.
- POWER1 and POWER2 inputs (operational range 4.1V to 5.7V, 0V to 10V undamaged)
- USB input (operational range 4.1V to 5.7V, 0V to 6V undamaged)
- Servo input: VDD_SERVO pin of FMU PWM OUT and I/O PWM OUT (0V to 42V undamaged)
Voltage monitoring
Pix32 v6 uses analog power modules.
Holybro makes various analog power modules for different need.
编译固件
TIP
Most users will not need to build this firmware! It is pre-built and automatically installed by QGroundControl when appropriate hardware is connected.
To build PX4 for this target:
make px4_fmu-v6c_default调试接口
The PX4 System Console and SWD interface run on the FMU Debug port.
The pinouts and connector comply with the Pixhawk Debug Full interface defined in the Pixhawk Connector Standard interface (JST SM10B connector).
| 针脚 | 信号 | 电压 |
|---|---|---|
| 1（红） | Vtref | +3.3V |
| 2 | Console TX (OUT) | +3.3V |
| 3 | Console RX (IN) | +3.3V |
| 4（黑） | SWDIO | +3.3V |
| 6 | SWCLK | +3.3V |
| 6 | SWO | +3.3V |
| 7 | NFC GPIO | +3.3V |
| 8 (blk) | PH11 | +3.3V |
| 9 (blk) | nRST | +3.3V |
| 10 (blk) | GND | GND |
For information about using this port see:
- SWD Debug Port
- PX4 System Console (Note, the FMU console maps to USART3).
外部设备
支持的平台/机身
Any multicopter / airplane / rover or boat that can be controlled with normal RC servos or Futaba S-Bus servos. The complete set of supported configurations can be seen in the Airframes Reference.