Skip to content

Video Streaming Data-link using WiFi in Raw Mode (WFB-ng)

This tutorial shows how to set up a companion computer with a Logitech C920 or RaspberryPi camera, such that the video stream is transferred from the UAV to a ground computer and displayed in QGroundControl. The setup uses WiFi in unconnected (broadcast) mode and software from the WFB-ng project.

The channel can also be used as a bidirectional telemetry link and TCP/IP tunnel for drone control during flight. If you manually control the drone with a Joystick from QGroundControl (which uses MAVLink) then you can use WFB-ng as single link for all drone communications (Video, MAVLink telemetry, remote control using a Joystick).

WARNING

Before using WFB-ng check regulators allow this kind of WiFi use in your country.

WFB-ng Overview

The WFB-ng project provides a data transport that use low-level WiFi packets to avoid the distance and latency limitations of the ordinary IEEE 802.11 stack.

The high level benefits of WFB-ng include:

  • Low-latency video link.
  • Bidirectional telemetry link (MAVLink).
  • TCP/IP tunnel.
  • Automatic TX diversity - use multiple cards on the ground to avoid antenna tracker.
  • Full link encryption and authentication (using libsodium).
  • Aggregation of MAVLink packets (pack small packets into batches before transmitting).
  • Enhanced OSD for Raspberry PI or generic linux desktop with gstreamer.

Additional information is provided in the FAQ below.

하드웨어

기체 설정

The vehicle setup consists of:

Ground Station

  • Ground Station Computer. These options have been tested:

    • Any Linux computer with a USB port (tested on Ubuntu 18.04 x86-64)
    • A computer with any OS running QGround control and Raspberry PI connected via Ethernet (RPi provides the wifi connection).
  • WiFi module ALPHA AWUS036ACH or any other RTL8812au card. See WFB-ng wiki > WiFi hardware for more information on supported modules.

Hardware Modification

Alpha AWUS036ACH is a medium power card that uses a lot of current while transmitting. If you power it from ordinary USB2 it will reset the port on most ARM boards. If you connect it to USB3 port via native USB3 cable to a Linux laptop you can use it without modification.

For Raspberry PI (UAV or ground) it must be directly connected to 5V BEC (or high current power adapter in case of ground pi) in one of two ways:

You must also add a 470uF low ESR capacitor (like ESC has) between card +5v and ground to filter voltage spikes. You should integrate the capacitor with a custom USB cable. Without the capacitor you can get packet corruption or packet loss. Be aware of ground loop when using several ground wires.

INFO

If you use a special "very" high power cards from Taobao/Aliexpress then you MUST power it as described above in ANY case.

UAV Configuration

  1. Download Raspberry PI image from latest wfb-ng release
  2. Flash it to the UAV Raspberry PI
  3. Reboot it and ssh with standard credentials (pi/raspberry).
  4. Run actions for air role as displayed in motd.
  5. Setup camera pipeline. Open /etc/systemd/system/fpv-camera.service and uncomment pipeline according to your camera (PI camera or Logitech camera)
  6. Open /etc/wifibroadcast.cfg and configure WiFi channel according to your antenna setup (or use default #165 for 5.8GHz)
  7. Configure PX4 to output telemetry stream at speed 1500 Kbps (other UART speeds doesn't match well to RPi frequency dividers). Connect Pixhawk UART to Raspberry Pi UART. In /etc/wifibroadcast.cfg uncomment peer = 'serial:ttyS0:1500000' in [drone_mavlink] section.

Using a Linux Laptop as GCS (Harder than using a RPi)

  1. On ground Linux development computer:

    sh
    sudo apt install libpcap-dev libsodium-dev python3-all python3-twisted
    git clone -b stable https://github.com/svpcom/wfb-ng.git
    cd wfb-ng && make deb && sudo apt install ./deb_dist/wfb-ng*.deb
  2. Follow the Setup HOWTO to complete installation

  3. Don't forget to copy /etc/gs.key from UAV side to ground side to bind two setups.

  4. Also don't forget to use the same frequency channel as on the UAV side.

Using Raspberry PI as GCS (Easier)

If you have Windows or OSX, or don't want to setup WFB-ng to your Linux laptop then you can use the same prebuilt image and another Raspberry Pi:

  1. Flash image to the ground Raspberry Pi.
  2. Reboot it and SSH in with standard credentials (pi/raspberry).
  3. Run actions for ground role as displayed in motd, but skip setup of fpv-video service and osd service.
  4. Connect your laptop and ground RPi via ethernet and configure IP addresses
  5. Edit /etc/wifibroadcast.cfg and set the IP address of the laptop in [gs_mavlink] and [gs_video] sections (replacing 127.0.0.1).

QGroundControl Setup

  1. Run QGroundControl and set RTP h264 on port 5600 as video source
  2. Use default settings (udp on port 14550) as mavlink source

Tuning Radio Settings

With default settings WFB use radio channel 165 (5825 MHz), width 20MHz, MCS #1 (QPSK 1/2) with long GI. This provides ~7 mbit/s of effective speed (i.e. usable speed after FEC and packet encoding) for both directions in sum, because WiFi is half-duplex. So it is suitable for video down stream 720p@49fps (4 mbit/s) + two full-speed telemetry streams (uplink and downlink). If you need a higher bandwidth you can use other MCS index (for example 2 or greater)

Antennas and Diversity

For simple cases you can use omnidirectional antennas with linear (that bundled with wifi cards) or circular leaf (circularly polarized Coverleaf Antenna) polarization. If you want to setup long distance link you can use multiple wifi adapters with directional and omnidirectional antennas. TX/RX diversity for multiple adapters supported out of box (just add multiple NICs to /etc/default/wifibroadcast). If your WiFi adapter has two antennas (like Alfa AWU036ACH) TX diversity is implemented via STBC. Cards with 4 ports (like Alfa AWUS1900) are currently not supported.

자주 묻는 질문

Q: What type of data can be transmitted using wfb-ng?

A: Any UDP with packet size <= 1445. For example x264 inside RTP or MAVLink.

Q: What are transmission guarantees?

A: Wifibroadcast uses FEC (forward error correction). You can tune it (both TX and RX simultaneously!) to fit your needs.

Q How far I can fly and still connect?

A It depends on your antennas and WiFi cards. With Alfa AWU036ACH and 20dBi patch antenna on the ground ~20km is possible.

WARNING

Don't use band that the RC TX operates on! Or setup RTL properly to avoid model loss.

Q: Is only Raspberry PI supported?

A: WFB-ng is not tied to any GPU - it operates with UDP packets. But to get RTP stream you need a video encoder (which encodes raw data from camera to x264 stream), or you must use a camera with a hardware video codec like Logitech C920 or Ethernet security cameras.

  • RPI3b/3b+/ZeroW. Prebuilt images are available, but it supports only h264 video for CSI cameras.
  • Jetson Nano. It supports h264 and h265 but you need to setup it yourself according to Setup HOWTO

You can use any other Linux ARM board, but you need to use an Ethernet or USB camera with built-in hardware video codecs (such as Logitech C920).

Theory

WFB-ng puts the WiFi cards into monitor mode. This mode allows to send and receive arbitrary packets without association and waiting for ACK packets. Analysis of Injection Capabilities and Media Access of IEEE 802.11 Hardware in Monitor Mode802.11 timings