Holybro Kakute H7 V2

WARNING

PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues.

The Holybro Kakute H7 V2 flight controller is full of features including integrated Bluetooth, HD camera plug, dual plug-and-play 4in1 ESC ports, 9V VTX ON/OFF Pit Switch, barometer, OSD, 6x UARTs, 128MB Flash for Logging (not supported with PX4 yet), 5V and 9V BEC, and bigger soldering pad with easy layout and much more.

The Kakute H7v2 builds upon the best features of its predecessor, the Kakute F7, and the Kakute H7.

The board also has an on-board barometer, LED & buzzer pad, and I2C pad (SDA & SCL) for external GPS/magnetometers.

INFO

This flight controller is manufacturer supported.

주요 특징

• MCU: STM32H743 32-bit processor running at 480 MHz
• IMU: BMI270
• Barometer: BMP280
• OSD: AT7456E
• Onboard Bluetooth chip: Disabled with PX4
• VTX On/Off Pit Switch: Not used with PX4
• 6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry)
• 9x PWM Outputs (8 Motor Outputs, 1 LED)
• 2x JST-SH1.0_8pin port (For Single or 4in1 ESCs, x8/Octocopter plug & play compatible)
• 1x JST-GH1.5_6pin port (For HD System like Caddx Vista & Air Unit)
• Battery input voltage: 2S-8S
• BEC 5V 2A Cont.
• BEC 9V 1.5A Cont.
• Mounting: 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets
• Dimensions: 35x35mm
• Weight: 8g

구매처

The board can be bought from one of the following shops (for example):

• Holybro

TIP

The Kakute H7v2 is designed to work with the Tekko32 4-in-1 ESC and they can be bought in combination.

커넥터 및 핀

핀	기능	기본값
B+	Battery positive voltage (2S-8S)
VTX+	9V Output
SDA, SCL	I2C 연결(주변장치용)
5V	5V 출력 (최대 2A)
3V3	3.3V output (0.25A max)
VI	FPV 카메라의 비디오 입력
VO	비디오 송신기로 비디오 출력
CAM	To camera OSD control
G 또는 GND	접지
RSI	수신기에서 아날로그 RSSI(0-3.3V) 입력
R1, T1	UART1 RX 및 TX	TELEM1
R3, T3	UART3 RX 및 TX	NuttX 디버그 콘솔
R4, T4	UART4 RX 및 TX	GPS1
R6, T6	UART6 RX and TX (R6 also located in the GH plug)	RC 포트
R7	UART7 RX (RX is located in the plugs for use with 4-in-1 ESCs)	DShot 텔레메트리
LED	WS2182 주소 지정이 가능한 LED 신호 와이어(테스트되지 않음)
Z-	피에조 부저 네거티브 레그(부저 포지티브 레그를 5V 패드에 연결)
M1에서 M4	모터 신호 출력 (4-in-1 ESC에서 사용하기 위해 플러그에 위치)
M5 to M8	모터 신호 출력 (4-in-1 ESC에서 사용하기 위해 플러그에 위치)
Boot	부트로더 버튼

부트로더 업데이트

The board comes pre-installed with Betaflight. Before the PX4 firmware can be installed, the PX4 bootloader must be flashed. Download the holybro_kakuteh7v2_bootloader.hex bootloader binary and read this page for flashing instructions.

펌웨어 빌드

To build PX4 for this target:

make holybro_kakuteh7v2_default

펌웨어 설치

INFO

KakuteH7v2 is supported with PX4 master & PX4 v1.14 or newer. If you are loading the pre-built firmware via QGroundcontrol, you must use QGC Daily or QGC version newer than 4.1.7. Prior to that release you will need to manually build and install the firmware.

Firmware can be manually installed in any of the normal ways:

• Build and upload the source:

  make holybro_kakuteh7v2_default upload

• Load the firmware using QGroundControl. 미리 빌드된 펌웨어나 사용자 지정 펌웨어를 사용할 수 있습니다.

INFO

KakuteH7v2 is supported with PX4 main and v1.14 or newer.

PX4 설정

In addition to the basic configuration, the following parameters are important:

매개변수	설정
SYS_HAS_MAG	보드에 내부 자력계가 없기 때문에 비활성화하여야 합니다. 외부 자력계를 연결하여 활성화 할 수 있습니다.

시리얼 포트 매핑

UART	장치	포트
USART1	/dev/ttyS0	TELEM1
USART3	/dev/ttyS2	디버그 콘솔
UART4	/dev/ttyS3	GPS1
USART6	/dev/ttyS4	RC SBUS
UART7	/dev/ttyS5	ESC 텔레메트리(DShot)

디버그 포트

시스템 콘솔

UART3 RX and TX are configured for use as the System Console.

SWD

The SWD interface (JTAG) pins are:

• SWCLK: Test Point 2 (Pin 72 on the CPU)
• SWDIO: Test Point 3 (Pin 76 on CPU)
• GND: As marked on board
• VDD_3V3: As marked on board