ZenFC H743

PX4 main (v2.0)

WARNING

PX4 не розробляє цей (або будь-який інший) автопілот. Contact the manufacturer for hardware support or compliance issues.

The ZenFC H743 is a flight controller designed by Zenithra Tech. It is built around the STM32H743 processor with dual Bosch BMI088 IMUs for sensor redundancy, an onboard barometer, and an integrated OSD.

INFO

This flight controller is manufacturer supported.

Основні характеристики

• MCU:
  • STM32H743VIT6 (32-bit Arm® Cortex®-M7, 480 MHz)
• IMU:
  • 2x Bosch BMI088 (accel + gyro, independent SPI buses for redundancy)
• Barometer:
  • Bosch BMP388
• OSD:
  • Onboard AT7456E OSD chip
• Interfaces:
  • 7x UARTs
  • 1x CAN
  • 2x external I2C (I2C1 with GPS connector and dedicated I2C2 connector)
  • 8x PWM outputs (Dshot supported)
  • microSD card slot
  • 1x USB Type-C
• Power:
  • 2x ADC (V_BAT & current sense)
  • Battery Input range - 2S-6S
  • BEC Outputs
    • 9V 3A cont.
    • 5V 3A cont.

Розміри

• Mounting: 30.5 mm x 30.5 mm /Φ4mm hole
• Dimensions: 35mm x 35mm x 8mm
• Weight: 9g

Де купити

Order from Zenithra Tech.

Flight Controller Layout

Налаштування послідовного порту

UART	Пристрій	PX4 Port
USART1	/dev/ttyS0	GPS1
USART2	/dev/ttyS1	TEL3
USART3	/dev/ttyS2	TEL4
UART5	/dev/ttyS3	TEL1
USART6	/dev/ttyS4	RC
UART7	/dev/ttyS5	TEL2
UART8	/dev/ttyS6	UART6

Connectors & Pinout

Board uses JST SH connectors for all interfaces.

Note - SBus pin on DJI O3/O4 port is internally connected to RX6 (RCIN).

PWM Виходи

The 8 outputs are in 3 groups:

• Outputs 1-4 in group1
• Outputs 5-6 in group2
• Outputs 7-8 in group3

Note:

• All outputs support PWM and DShot protocol. Outputs 1-6 and 8 support "bidirectional DShot" (or "BDShot") telemetry.
• Outputs 1-4 default to DShot300 (PWM_MAIN_TIM0 = -4); outputs 5-6 and 7-8 default to PWM at 400 Hz.
• Each group's protocol can be changed independently using the corresponding PWM_MAIN_TIMx parameter, including to Bidirectional DShot (BDShot) for ESC telemetry.

Відладочний порт

This board does not configure a dedicated UART as a system console. Use the MAVLink Shell over USB for console/NSH access using QGroundControl.

SWD

The board features a 4-pin SWD Debug interface (3V3 / SWCLK / SWDIO / GND) for hardware debugging.

Радіоуправління

A Radio Control (RC) system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes). See Radio Control modules for the list of supported protocols.

RC input is mapped to USART6 (/dev/ttyS4, RC port). The port supports both single-wire inverted SBUS and full-duplex protocols with telemetry return (such as CRSF), and the receiver protocol is auto-detected by default (RC_INPUT_PROTO = -1).

Конфігурація PX4

In addition to the basic configuration, the following parameter is important:

Parameter	Налаштування
SYS_HAS_MAG	Disabled by default since the board has no internal magnetometer. Enable it if you attach an external mag.

Збірка прошивки

To build PX4 for this target:

make zenfc_h743_default

Встановлення прошивки PX4

Прошивку можна встановити будь-якими звичайними способами:

• Збудуйте та завантажте джерело:

  make zenfc_h743_default upload

• Load the firmware using QGroundControl. Ви можете використовувати або готове вбудоване програмне забезпечення, або власне користувацьке програмне забезпечення.

The board uses the standard PX4 bootloader, so it follows the same generic LED indications as most other boards (Red = Bootloader/Error, Blue = Active/Activity, Green = Powered).

Подальша інформація

• Zenithra Tech