Agam Autopilot v6X-RT

main (PX4 v2.0)

WARNING

PX4 не розробляє цей (або будь-який інший) автопілот. Contact the manufacturer for hardware support or compliance issues.

The Agam Autopilot v6X-RT flight controller is Agam Robotics' implementation of the NXP-led FMUv6X-RT reference design.

INFO

This flight controller is manufacturer supported.

Введення

Agam Autopilot v6X-RT uses the NXP i.MX RT1176 MCU, consisting of an Arm® Cortex®-M7 core at 1GHz and an Arm® Cortex®-M4 core at 400MHz, with 2MB SRAM and 64MB Octal SPI flash. The increased processing power lets firmware developers run more complex algorithms without being constrained by the flight controller's compute budget.

The board uses sensors from InvenSense® and Bosch®, and ships in two sensor-set variants (see Processors & Sensors). Redundant IMU and barometer sensors sit on separate buses, and 2 of the 3 IMUs are mounted on a shock-isolated, heated sensor board, separate from the FMU board itself, to improve accuracy in flight and across a wide temperature range.

An integrated Ethernet interface (100BASE-T1, 2-wire) provides high-speed, low-latency connectivity to companion computers (for example a Raspberry Pi or NVIDIA Jetson), cameras, or data-transmission systems.

Ключові пункти дизайну

• High-performance NXP i.MX RT1176 dual-core MCU
• NXP EdgeLock SE051 hardware secure element, field-updatable, certified to CC EAL 6+
• Triple redundant IMU (2 sensors on a shock-mounted, heated sensor board, 1 on the FMU board itself) and dual redundant barometer, each on a separate bus
• Independent power control and separate buses for each sensor domain
• 100BASE-T1 (2-wire) automotive Ethernet for high-speed companion computer integration
• 256Kbit FRAM

TIP

This board ships with SENS_IMU_MODE and EKF2_MULTI_IMU set so that only the FMU-board IMU is used by default. To take advantage of the triple-redundant IMU set SENS_IMU_MODE to Disabled (0), reboot, set EKF2_MULTI_IMU to 3, and reboot again. See Agam's IMU triple redundancy notes for more information.

Processors & Sensors

• FMU Processor: NXP i.MX RT1176 (MIMXRT1176DVMAA)
  • Arm® Cortex®-M7 core @ 1GHz
  • Arm® Cortex®-M4 core @ 400MHz (secondary core)
  • 2MB SRAM
  • 64MB external Octal SPI flash
• On-board sensors — Agam Autopilot v6X-RT ships in two sensor-set variants (Sensor Set 1 and Sensor Set 3, per Pixhawk Standards):
  • Sensor Set 1:
    • 2x InvenSense ICM-42688-P IMU
    • Bosch BMI088 IMU
    • Bosch BMM150 Magnetometer
    • 2x Bosch BMP388 Barometer
  • Sensor Set 3:
    • 2x TDK InvenSense ICM-45686 IMU
    • Bosch BMI088 IMU
    • Bosch BMM350 Magnetometer
    • 2x Bosch BMP388 Barometer

Електричні дані

• Номінальна напруга:
  • Максимальна вхідна напруга: 6 В
  • Вхід USB Power: 4.75~5.25V
  • Вхід Servo Rail: 0~36V
• Номінальний струм:
  • TELEM1 output current limiter: 1.5A
  • Комбінований обмежувач вихідного струму всіх інших портів: 1.5A

Механічні характеристики

• Розміри
  • Flight controller module: 39 x 32 x 16 mm
  • Baseboard: 95 x 50 x 19 mm
• Weight: 90 g
• Operating temperature: -40°C to 85°C

Інтерфейси

• 12 PWM/DShot outputs (8 DShot-capable, 4 PWM-only)
• 1x RC input, SBUS/PPM
• 1x dedicated DSM/Spektrum RC input
• 3x TELEM ports (TELEM1, TELEM2, TELEM3), full flow control
• 2x GPS ports (GPS1 full GPS plus safety switch and buzzer, GPS2 basic)
• 4x I2C
• 3x CAN-FD
• 1x SPI bus, 2 chip-select lines, 2 data-ready lines, 1 sync line, 1 reset line
• 1x NFC antenna port (connected to the SE051 secure element)
• 100BASE-T1 Ethernet (single 2-wire port)
• USB 2.0
• microSD card slot
• Dual redundant power input (5V via Molex connectors)

Where To Buy

Order from the Agam Robotics store.

Зборка/інсталяція

Agam Autopilot v6X-RT is a Pixhawk-standard v6X-RT board, electrically and mechanically identical to the NXP reference design, differing from it only in enclosure. Wiring is similar to the Holybro Pixhawk 6X and other boards that follow the Pixhawk Connector Standard.

For wiring and assembly, follow the Pixhawk 6X Wiring Quick Start, which applies to this board other than the enclosure.

З'єднання

The connectors follow the Pixhawk Connector Standard, which defines the pinout of each port type. For the physical layout of the ports on the board see the Agam Autopilot v6X-RT baseboard ports documentation.

Схема розташування виводів

Agam Autopilot v6X-RT's pinout is the same as other v6X-RT-family boards:

• DS-012 Pixhawk Autopilot v6X Standard
• DS-010 Pixhawk Autopilot Bus Standard
• DS-009 Pixhawk Connector Standard
• Agam Autopilot v6X-RT Baseboard Port pinouts (agamrobotics.gitbook.io)

Notes:

• The camera capture pin (PI0) is pin 2 on the AD&IO port, marked FMU_CAP.

Налаштування послідовного порту

UART	Пристрій	Порт
LPUART1	/dev/ttyS0	Консоль
LPUART3	/dev/ttyS1	GPS
LPUART4	/dev/ttyS2	TELEM1
LPUART5	/dev/ttyS3	GPS2
LPUART6	/dev/ttyS4	PX4IO
LPUART8	/dev/ttyS5	TELEM2
LPUART10	/dev/ttyS6	TELEM3
LPUART11	/dev/ttyS7	EXT2

Radio Control

Для того щоб керувати транспортним засобом вручну, потрібна система радіоуправління (RC) (PX4 не потребує системи радіоуправління для автономних режимів польоту). Вам потрібно вибрати сумісний передавач/приймач і зв'язати їх таким чином, щоб вони взаємодіяли (ознайомтеся з інструкціями, що додаються до вашого конкретного передавача/приймача).

The ports and supported protocols are:

• RC IN (FMU): SBUS/PPM
• DSM RC (FMU): Spektrum/DSM

For PPM and S.Bus receivers, a single signal wire carries all channels. If your receiver outputs individual PWM signals (one wire per channel) it must be connected via a PPM encoder.

Номінальна напруга

Agam Autopilot v6X-RT can be triple-redundant on the power supply if three power sources are supplied. The three power rails are: POWER1, POWER2 and USB. The POWER1 & POWER2 ports use a 6-circuit 2.00mm Pitch CLIK-Mate Wire-to-Board PCB Receptacle.

Максимальна напруга нормальної роботи

За таких умов всі джерела живлення будуть використовуватися в цьому порядку для живлення системи:

1. POWER1 and POWER2 inputs (4.9V to 5.5V)
2. USB input (4.75V to 5.25V)

Абсолютна максимальна напруга

За таких умов система не буде витрачати жодної потужності (не буде працювати), але залишиться неушкодженою.

1. POWER1 and POWER2 inputs (operational range 4.1V to 5.7V, 0V to 10V undamaged)
2. USB input (operational range 4.1V to 5.7V, 0V to 6V undamaged)
3. Servo input: VDD_SERVO pin of FMU PWM OUT (0V to 42V undamaged)

Digital I2C battery monitoring is enabled by default. Analog/ADC battery monitoring is also supported.

Збірка прошивки

TIP

Most users will not need to build this firmware from PX4 v2.0. It will be pre-built and automatically installed by QGroundControl when appropriate hardware is connected.

To build PX4 for this target:

make agam_fmu-v6xrt_default

Debug Port

The PX4 System Console and SWD interface run on the FMU Debug port.

The pinout and connector comply with the Pixhawk Debug Full interface defined in the Pixhawk Connector Standard (JST SH 1mm pitch, 10-pin connector). Pin 6 is SPI6_MOSI_EXTERNAL1, which is the pad's JTAG_TDO function and carries SWO when the debug port is in serial-wire mode.

Pin	Сигнал	Вольтаж
1 (red)	FMU_VDD_3V3	+3.3V
2 (black)	FMU_USART_TX	+3.3V
3 (black)	FMU_USART_RX	+3.3V
4 (black)	FMU_SWD_IO	+3.3V
5 (black)	FMU_SWD_CK	+3.3V
6 (black)	SWO	+3.3V
7 (чорний)	NFC GPIO	+3.3V
8 (чорний)	PH11	+3.3V
9 (чорний)	FMU_nRST	+3.3V
10 (чорний)	GND	GND

Інформацію про використання цього порту див:

• SWD Debug Port
• PX4 System Console

Периферійні пристрої

• Agam GNSS01 CAN
• Agam GNSS02 CAN RTK
• Agam GNSS Base RTK
• Agam FloRange Sensor
• Rangefinders/Distance sensors
• Telemetry Radio Modules

Подальша інформація

• Update Pixhawk 6X-RT Bootloader
• Agam Autopilot v6X-RT Documentation (Agam Robotics Docs)
• Agam Autopilot v6X-RT setup video playlist (YouTube, Agam Robotics)
• Pixhawk 6X Wiring QuickStart
• Agam Digital Power Module (DPM01)
• Agam Analog Power Module (APM)
• Announcing the Pixhawk FMUv6X-RT (Dronecode Foundation)
• Pixhawk FMUv6X-RT open standard
• Стандарт шини автопілота Pixhawk
• Стандарт Pixhawk Connector Standard