Посилання на модулі: Baro (драйвер)
bmp280
Source: drivers/barometer/bmp280
Usage
bmp280 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 118
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
stop
status print status infobmp388
Source: drivers/barometer/bmp388
Usage
bmp388 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 118
stop
status print status infobmp581
Source: drivers/barometer/bmp581
Usage
bmp581 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 70
stop
status print status infodps310
Source: drivers/barometer/dps310
Usage
dps310 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 119
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-8] Drive DPS368
stop
status print status infoicp101xx
Source: drivers/barometer/invensense/icp101xx
Usage
icp101xx <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 99
stop
status print status infoicp201xx
Source: drivers/barometer/invensense/icp201xx
Usage
icp201xx <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 99
stop
status print status infolps22hb
Source: drivers/barometer/lps22hb
Usage
lps22hb <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
stop
status print status infolps25h
Source: drivers/barometer/lps25h
Usage
lps25h <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
stop
status print status infolps33hw
Source: drivers/barometer/lps33hw
Usage
lps33hw <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 93
[-k] if initialization (probing) fails, keep retrying periodically
stop
status print status infompc2520
Source: drivers/barometer/maiertek/mpc2520
Usage
mpc2520 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 118
stop
status print status infompl3115a2
Source: drivers/barometer/mpl3115a2
Usage
mpl3115a2 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 96
stop
status print status infoms5611
Source: drivers/barometer/ms5611
Usage
ms5611 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-T <val>] Device type
values: 5607|5611, default: 5611
stop
status print status infoms5837
Source: drivers/barometer/ms5837
Usage
ms5837 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
stop
status print status infospa06
Source: drivers/barometer/goertek/spa06
Usage
spa06 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 118
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
stop
status print status infospl06
Source: drivers/barometer/goertek/spl06
Usage
spl06 <command> [arguments...]
Commands:
start
[-I] Internal I2C bus(es) (onboard sensors; shared bus only if -b is
given)
[-X] External I2C bus(es) (connector sensors, including shared
buses)
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
[-a <val>] I2C address
default: 118
[-s] Internal SPI bus(es) (onboard sensors; shared bus only if -b is
given)
[-S] External SPI bus (connector sensors, including shared buses)
[-b <val>] board-specific bus (default=all) (external SPI: n-th bus
(default=1))
[-c <val>] chip-select pin (for internal SPI) or index (for external SPI)
[-m <val>] SPI mode
[-f <val>] bus frequency in kHz
[-q] quiet startup (no message if no device found)
stop
status print status info